Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Abingdon, VA – Tree Cutting & Portable Sawmill

LV Twin Screw Vise--using the '1/2 link'

Posts

LV Twin Screw Vise--using the '1/2 link'

#1

LV Twin Screw Vise--using the '1/2 link'

Wiley Horne--So. Calif.

Warning: This post will be understandable only by LV Twin Screw Vise users, but there are enough of them that it may do someone some good.

A few months ago, I installed my third LV Twin Screw Vise. Thought I was an expert. But this third vise has been doing an annoying thing because of a faulty decision I made at the initial installation. I finally figured out my mistake, and just fixed it. I want to relate the indications and the fix, in hopes it may help someone.

This particular vise is the 24" model. But the span I needed was about 19"+ or - center to center between the main vise screws. I didn't think much about it, just went ahead and drilled the jaws for the main screws, installed them, and then went to LV's instructions to see how many links I should remove from the chain to make it fit.

As luck would have it, my drilling was such that (now I'm making these numbers up) 48 links was too short, but 49 links was a little long. So I made it 49 links and thought no more about it. Went ahead and did the chain install and started using the vise.....

Well, the vise worked, but from time to time it did something that neither of my other ones did--every now and then there would be kind of a weird lurch, or momentary loss of traction; then the vise would instantly catch again and be normal. Except that the slippage, or whatever it was, was misaligning the screws little by little.

Now I admit to being dumb, but I'm not stupid. Yet I could look right at the chain as this odd lurch occurred, and it was so fast like instant coffee, that I couldn't make out what was going on. Plus I needed to get on with things, so I just lived with it.

Finally, it occurred to me in bed before I went to sleep one night, what was going on. When the chain is a little long--not so long you can take a full link out, but just a little long--it can furl up on the slack side as you spin the drive sprocket. In other words, as you spin the drive-side sprocket, the bottom of the chain will be taut, and the top will be slack (or vice versa). Also, the chain has a little 'body' in it; it's not perfectly limp. So when the chain is a little too long, the slack side has enough body to start furling up--enough to furl it's way all the way around the drive sprocket--and every link of the chain will find its way to the next tooth on the sprocket. Yes, the chain will actually rear up and reposition itself on the drive sprocket so that every link gains a tooth. This all happens so fast, you can't actually see it.

As I start getting my head wrapped around this, I then realize 'Oh, this is why LV includes a half-link in the vise kit'. Get out the instructions--yep, there's just enough slack that I can use this half-link to shorten the chain by a half link. Take out a full link, put in the half link. We're talking about shortening a 19" chain by 3/16". But it makes all the difference. Now the vise works perfectly.

Two suggestions relative to LV Twin Screw vises:

1. If you're having weird slippage as described above, test the chain for slack (as shown in the LV instructions). You may need to shorten the chain by a half-link.

2. And more important....At the initial installation, if you're not using the full length of the chain, be smart about how you place the twin screws. Pick a center-to-center distance for the screws which corresponds to a specific number of links in the chain--48 links, 49 links, 52 links, whatever--but don't use a center-to-center distance which falls between links. It's asking for misery. Incidentally, each link of the chain represents 3/8", so there will surely be enough flex in your installation that you can place the screws to correspond to a round number of links.

That's my story for tonight.

Wiley

Re: LV Twin Screw Vise--using the '1/2 link'

#2

Re: LV Twin Screw Vise--using the '1/2 link'

charlie belden

I'd have to take the chain caps off of mine to verify this - but I recall my Twin Screw Kit came with a "hip screw" and nylon sleeve what could spin on the screw. Acts like an idler pulley and takes out slack in the chain. Seems a simpler solution. Install everything, put the chain on with a little slack and screw in the "idler" to remove undesired slack.

Re: LV Twin Screw Vise--using the '1/2 link'

#3

Re: LV Twin Screw Vise--using the '1/2 link'

Wiley Horne--So. Calif.

Hi Charlie,

There's lots of common sense in what you say, and I went back and re-read the instructions carefully as part of the exercise described above.

Lee Valley states twice--two times--and very clearly--not to use the chain supports to take up slack. They say to place the supports so that the chain is not deflected inside the line where it is taut.

I didn't try it because of LV's admonition, plus I figured it would be at best a noisy solution, and temporary because the steel chain beating against the support might wear it out pretty quickly. On the other hand, shortening the chain takes noise out of the system, and eliminates the need for the supports.

Intuitively it has some appeal, and might work for a while, but LV says 'no'. BTW, it's not difficult to shorten the chain if you have a grinder to chew the rivets off of the link you want to remove. Doing it by handfiling alone takes a while longer, but I've done it.

Wiley

Re: LV Twin Screw Vise--using the '1/2 link'

#4

Re: LV Twin Screw Vise--using the '1/2 link'

ThomD

This should be appended to their instruction booklet, which is not detailed enough by half!

Sorry couldn't resist...

Re: LV Twin Screw Vise--using the '1/2 link'

#5

Get Thee To A Bicycle Shop

charlie belden

My youngest has been involved in the bicycle business since he was 13 or 14 (he's now 33). Any bike shop will have a tool called a Chain Cracker that'll pop out bike chain pins without damaging or even scratching anything. They go for around $10.

Regarding chain chatter/misaligning - it'll happen when you're tightening the jaws, not often when loosening. Not true of course if you use the vise for spreading as well as clamping.

I do recall the instructions stating something to the effect of "I know you think you can install this vise properly without reading the instructions - and following them.

DON'T! Read and follow the instructions - and save yourself some grief".

Re: LV Twin Screw Vise--using the '1/2 link'

#6

Re: Get Thee To A Bicycle Shop

Paul M.

That was my first thought too. If you show up at a bike shop with your chain and happen to have a frosty six-pack of quality lager with you, you can usually negotiate a small maintenance like shortening a chain without having to spend any money. You might have to walk away without the frosty beverages though. That seems to be the universal units of barter with bike mechanics.