Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Fast and affordable laser cutting – so you can make the parts you can’t find anywhere else

The Carousel Shooting Board Fence

Posts

The Carousel Shooting Board Fence

#1

The Carousel Shooting Board Fence

Derek Cohen (in Perth, Australia)

Well I finished painting today. While I was busy I had time to mull over a design for a shooting board fence. Some of you may have seen the recent fence I built, modelled after the Stanley #52. I thought this one deserved a fresh thread as it is a new design.

The design was inspired by a question I was asked on the Ubeaut forum (where I offered to make up a few fences for forum members) - could I make a left-handed version? My first response was to say 'yes' and consider a simple mirror image of the RH model. But I got to thinking about this while painting, and I had this idea for a combined model. I was quite excited about this design, and managed to make first a prototype, then just squeezed in a preproduction version before I was called for dinner.

I had second thoughts about making a fence with more than 45 degrees and 90 degrees. The times when other angles may be used is very infrequent. More useful would be the ability to shoot in both directions, which is important in mitred joints, such as picture frames.

So here is what I came up with. I call it the Carousel Shooting Board Fence as it is based on a circle. It has been tested with vigour as I was concerned that heavy use may move the fence. But it did not - the fence is very solid.

Note that this is a completed version, but it is on a very basic shooting board base. As you will see, there are a few options here, all up to the user.

The fence set for a square cut ...


Dimensions: The fence is 7 1/2" wide and 4" deep. (Note that I am using on old subfence on this preproduction version. The eagle-eyed will note the unevenly set fence bolts)

Here is the mitre setting ...


If all you want is a standard shooting board, then just stop at this point. However what the fence has designed into it is the facility to add a second runway (I did not have a base with then so you see a mock up below). Now you can either use it left-handed or you can swing the fence around so that you may shoot a joining mitre ...


Installation is similar to the #52 version - requires drilling two holes and using two very simple set up tools. I will have pictorial up on my website shortly for those wishing to make their own.

Regards from Perth

Derek

Re: The Carousel Shooting Board Fence

#2

Re: The Carousel Shooting Board Fence

Andrew F in Australia

Hi Derek,

Looks good.

As I alluded to in the last post of yours on the shooting boards, a lot of the kids I teach tend to roll the plane over, chewing out the fence and putting all off-square. The fix is simple - make the fence higher than the plane, so that the top of the blade can't cut off all the fence.

If you're going to make a tutorial up, it may be worth mentioning.

Cheers,

Andrew

Re: The Carousel Shooting Board Fence

#3

Re: The Carousel Shooting Board Fence

Derek Cohen (in Perth, Australia)

Hi Andrew

Thanks for the idea. I had not thought of the fence height as a means of controlling planing. Interestingly, Jeff Gorman suggested something similar, but as a means of controlling the shavings ... "the lateral margins of the plane would prevent the blade taking more than a couple of shavings from its end".

Jeff did warn "be careful where he puts his thumb while planing. Don't ask me ...............! "

I think that this is an issue of technique. There is not enough lateral downforce to pin the plane against the sidewall. One is likely to tip a plane if you put your downforce on the inside of the plane. I think that your school should supply the kids with a fleet of Stanley #51/52s! :)

Regards from Perth

Derek

Re: The Carousel Shooting Board Fence

#5

This is very impressive work *LINK*

Bill Houghton, Sebastopol, CA

but I have to ask: haven't you just invented the miter gauge? I'm thinking in particular of the Woodhaven gauge (linky below).

I wonder (not to be disrespectful of your work, Derek, which is, as always, not just highly developed technically but also really good looking) how well it would work to pick up a garage sale tablesaw miter gauge, mount it on the baseboard, and fill in each side of it with an appropriate thickness of board, planed parallel to the gauge bar?


http://www.amazon.com/Woodhaven-4901-Deluxe-Miter-Gauge/dp/B000BNA07Y/&tag=toolcribcom130-20

Re: The Carousel Shooting Board Fence

#6

Re: This is very impressive work

Pam Niedermayer - Austin, TX

Geesh, Bill, that was my reaction, but I figured it was way to negative to post. :)

Pam

Re: The Carousel Shooting Board Fence

#7

Re: This is very impressive work

Derek Cohen (in Perth, Australia)

Hi Bill and Pam

It occurred to me later that one could convert an old mitre gauge into a fence base .... after building this one I looked at it and said to myself, "that looks familiar!" :) ... which comes from following a concept in one's mind.

So, no, neither of you are "disrespectful" .... is that not the essence of problem-solving (and one of the reasons we do this thing called woodworking)? I love this type of thinking!

Bill, it may be a mite expensive using the mitre gauge you linked, but there is no reason why you could not find an orphan somewhere.

Issues with converting a mitre gauge (off the top of my head): how to attach it to the tabletop, how to secure it so that it does not shift/is it solid enough, is it wide enough to support a fence, and can the fence be adjustable for extension?

Regards from Perth

Derek

Re: The Carousel Shooting Board Fence

#8

Re: This is very impressive work

Pam Niedermayer - Austin, TX

Why not set up a system much like a table saw? Make a groove in the shooting board to accept the rod on the miter gauge for longitudinal placement, then add the wooden fence and start shooting.

Pam

Re: The Carousel Shooting Board Fence

#10

Re: This is very impressive work

Bob Hackett

After pawing thru my vast collection of miter gauges from the dump.I found that even the good ones(50+ years old by my eye) did not have stops to register into.

2 had spring detents at 90 and 45 and that was it.

The fence thing was good as most had provisions to attach things both to the face and also threaded holes(some with thumbscrews still) parallel to the fence.

While the pointers were adjustable for accuracy none were accurate thru the entire range when adjusted to 90.

I`d say the big difference would be the accuracy of the stops.

The negative would be infinite adjustment thru a 180 range but that`s easily added to Derek`s design.

So I`m going with the stops and accuracy of those stops as the reason to build Derek`s version.

MB

Re: The Carousel Shooting Board Fence

#11

Re: This is very impressive work

Pam Niedermayer - Austin, TX

A couple of adjustable screws to attach the wooden guide to the gauge, a marked 180� semicircle in front of the fence for determining angles (a table saw's inaccuracy is mostly due to a wobbling blade), and a means of clamping for angle holding. Fairly obvious stuff.

The cool thing is you could make the wooden guide to span the width of the board, which would give you the option of two stages, one each for left and right handed planing. You'd only have to reposition the wooden guide via the adjustable screws if you weren't working at 90�, since the wooden guide would be slightly too short.

You may want to think some more about the ends of the wooden guide, maybe round them off so you'd get sufficient support of the piece's ends. Or squared if you'd only work at 45� and 90�. I'd need to mock up a test guide to figure this out. At any rate, the full guide length would have to fully support the planed piece at their conjoined plane.

Pam

Re: The Carousel Shooting Board Fence

#12

Re: The Carousel Shooting Board Fence

Joe Rogers, Northern Virginia

Nice work as ususal Derek.

JR

Re: The Carousel Shooting Board Fence

#13

Not worth the effort, needlesss to say...

Scott Burr in Ben Lomond CA

A total waste of time IMHO. By using drill bushings and Derek's method of indexing a fence a "miter slot" would be a complete waste of time when compared to a simple ramp of platform with a, as Bill said "miter gauge". I'm all for the less variables the better as far as accuracy goes :)

Re: The Carousel Shooting Board Fence

#14

Re: Not worth the effort, needlesss to say...

Pam Niedermayer - Austin, TX

But one of Derek's goals was to make both a left and right handed capability. Waste of time? All kinds of ways to judge that, and, after all, Derek may find something interesting in the process and/or result.

Pam

Re: The Carousel Shooting Board Fence

#15

Not a waste of time...

Scott Burr in Ben Lomond CA

It's quite easy. No slots or nothing, just make sure the fence(s) are parallel.

Sorry for quick and sloppy sketch everyone.

Re: The Carousel Shooting Board Fence

#16

Re: Not a waste of time...

Pam Niedermayer - Austin, TX

I think the slot is needed to get the gauge at the same level as the board and still able to swing.

Pam

Re: The Carousel Shooting Board Fence

#17

Re: This is very impressive work

ThomD

Not so easy making really accurate stops, while it is very easy to make really accurate lines on a piece of scrap wood mount a fence, and a single angle shooting board is born.

One way of getting nice accurate readings in the round is to start with a Stadler 360 degree protractor or similar, measure it up and draw and outbound series of increments of the same scale, in CAD, where each increment is worth 1.1 of the protractor increments. Print. Bingo, highly accurate vernier scale for your protractor.

One thing about those miter fences is they tend to move away from the cutpoint as you rotate them. More complications compared to the stick and glue models.

Re: The Carousel Shooting Board Fence

#18

Say what!?!

Scott Burr in Ben Lomond CA

Why would it need a slot to move? We're not talking about an adjustment up and down the shooting board.

We're talking about a rotational movement around a center point of the protractor head.

I could remove the guide bar from my miter gauge and the protractor head will still move freely on the surface of the saw. No slot needed just an axis to spin.

Re: The Carousel Shooting Board Fence

#19

True, though I think Pam had the same idea I did

Bill Houghton, Sebastopol, CA

or a similar one, anyhow.

my thought was: take miter gauge; fasten bar to baseboard; install parallel-sided wood pieces the thickness of the miter bar, one each side of the miter gauge; make and install sliding fence on the miter gauge so that you can support the work right up to the edge, as Derek's design does.

Here I am left-handed, and I hadn't thought, until Pam mentioned it, that this design allows for rightie or leftie shooting, just as Derek's can.

Re: The Carousel Shooting Board Fence

#20

Thanks for the explanation Bill.

Scott Burr in Ben Lomond CA

I understand what your getting at, makes sense to me now. Still with a design like that there is a tolerance stack up that concerns me.

Re: The Carousel Shooting Board Fence

#21

Yeah, pretty much exactly what I had in mind.

Pam Niedermayer - Austin, TX

Re: The Carousel Shooting Board Fence

#22

Reality?

Derek Cohen (in Perth, Australia)

Hi Pam

I managed to have a look at a mitre gauge today, one more typical of the type that might be coopted for a shooting board.

The gauge is one that came with my tablesaw when I purchased it about 15 years ago. It was not used much as my tablesaw has a sliding table, and eventually I modifed it for use with my Hammer bandsaw (which has a unusually shallow track).


While I do not see any difficulty attaching this gauge to the centre of the board, or making it swivel, the gauge has two major problems that make it unsuitable for use on a shooting board (at least, as replacement for the design I outlined earlier).

Firstly, there is no where to attach a sliding fence, unless one builds a subfence.


Secondly, the construction is cast aluminium and, while sturdy enough for a tablesaw, I doubt that it is rugged enough for the type of repeated impact that it would receive on a shooting board.


Soooo ... unless someone can come up with a better guage (that does not cost more than $10), I guess you would be better off making one.

Regards from Perth

Derek

Re: The Carousel Shooting Board Fence

#23

Re: Reality?

Pam Niedermayer - Austin, TX

I had assumed that the gauge would have to be drilled or otherwise modified to attach a wooden fence. Don't know how strong is necessary. When I'm shooting, I don't apply much impact pressure; but it's possible that there's more pressure from being hit than from hitting (sliding into a spinning blade).

Pam