Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Identify and use hundreds of woods

Freezing wood?

Posts

Freezing wood?

#1

Freezing wood?

Edward in Vancouver

>My next project will be very utilitarian-- I have to make some new shelves for my stand-up double door fridge, and double-door freezer at work. These are commercial units, and the standard plastic-coated wire shelves are driving me nuts! Firstly the plastic is fatiguing and cracking off--in spite of only being a few yers old, and secondly, the wire shelves bend when they recieve anything more than 10-15 lbs, and then they pop out of the s/s channels that hold them in place.

So I was thinking of making wood shelves, aprox 3/4" thick and about 20" x 28", a frame basically of about 2-3" wide members with a center strip of the same and maybe 2 cross pieces--the shelves don't need to be solid.

Hardwood, but what? Soft maple is cheaper than Birch, and the shelves don't need to be pretty, just tight joints and "strong like tractor". I as thinking half-lap joints, maybe pinned with home-made dowels of the same wood. Finish is important--no film finishes, no toxic stuff, probably just mineral oil--re-treated when neccesary.

I need to make 12 of them, actually 14 would be nice. Humidity in the fridge would be around 80%, freezing temps in the freezer and the usual defrost cyles, so there will be condensation and water/ice forming on the shelves at times.

Does any hardwood stand up better than others in these temps/conditions? Would a decent outdoor glue like Titebond work? If provoked, I could use mechanical fastners, but I'd have to go to brass or s/s, and I'd rather avoid this.

Suggestions?

Re: Freezing wood?

#2

Re: Freezing wood?

Bob Hackett

>At 80% humidity I would treat this like boatbuilding and look for marine grade hardware and wood.

Wood like teak,mahogany,angelique,white oak,southern yellow pine or marine grade ply.

I`d think about using an epoxy like West System or an equivalent and use either SS or bronze hardware.

For finishing,according to at least one famous finisher most any finish is actually food safe once it`s cured.

I still stay away from oil finishes with heavy metal driers added though.Poly or something like spar varnish would be most durable and easier to clean I would think.

Anyway you could do worse than treating this project like a boat.Boats withstand high humidity(they mostly live in water) and sometimes periods of down to 11% when they`re hauled out and stored here on the coast of Maine.They also must go from 90 degree heat during the summer to below zero during the long months of winter.All while putting up with the indignity of dealing with humans and their rather odd habits on a day to day basis.

MB

Re: Freezing wood?

#3

Concur, from slightly difference experiences

Bill Houghton

>DON'T use maple or birch. You're basically, especially in the fridge, replicating outside conditions in terms of humidity, and they won't last. Choose a wood suitable for outside use.

Some many years back, my father built a sliding window for our bathroom. He proudly showed me the track he'd made for little nylon wheels to run on, making the sliding window more of a gliding window. The trouble came from his choice of maple for the track. It lasted longer than could reasonably be expected, but, when it failed, did so by turning into track-shaped rot, about as strong as typing paper - no, less so.

It's possible that Doug fir would be an affordable choice; it's relatively durable in the weather, and you can probably get it easily in Vancouver. But I think I'd go for one of the more durable woods yet. I can't add any others to the list Bob presented.

Re: Freezing wood?

#4

Black locust...

Jorge Casta�eda

>Ed,

I suggest, white oak or black locust or long leaf yellow pine specially if you can get it with the pitch on it, from a tree that was not tapped for turps.

Epoxy the joints and use same as a finish, with that humidity you really need it to be water tight. Epoxy degrades from UV exposure, but inside a freezer I don't think you need to worry about it. And will be tough and stand up to wear and will be easy to wipe clean.

Jorge

Re: Freezing wood?

#5

what is the issue with driers?

Bill Tindall

>What is the perceived problem posed by driers? They aren't volatile and people don't typically eat varnish. So how can they possibly be harmful?

Modern driers are typically some cobalt compound. The red stuff you put in Bondo is a cobalt compound. Is Bondo to be avoided, and oil based paint? While some large amount of cobalt is undoubtedly toxic, cobalt is an essential mineral and small amounts are required, at least by sheep and cows. It is always added to my sheep mineral mixes and in some regions "salt" blocks with cobalt are necessary. It would seem that the amount of cobalt I get from eating the sheep that eat the mineral mix would be greater than what anyone would get from varnish.

Re: Freezing wood?

#6

Just my thoughts about driers

Bob Hackett

>Anything to do with heavy metals I shy away from as much as possible.

It may be only in my imagination that there may be a chance of an oil finish containing driers even slightly contaminating food that comes in contact with it but it still is outside my comfort level.

I have no problem with any finish that forms a hard shell such as varnish etc.

I use Japan driers in some exterior finishes for furniture and don`t worry about absorbing it thru my skin so may be I`m too careful about this.

After having problems with both zinc and bronze/brass exposure and the resulting effects I did some research and no longer weld or grind cad plated or galvanized anything.My wife and I are very particular about what we put in our bodies and ANY amount of a metal that can accumulate in the body is to be avoided.I shudder to think about playing with mercury when I was a kid.

May be just one of my many quirks Bill.I figure as long as I`m thinking about it I`ll reduce the exposure and that can`t be a bad thing.

Took me a long time to get my head around the idea that most finishes are food safe.I still finish my bowls and other treen with mineral oil and beeswax exclusively though.Call me an old dog.

Mainely,Bob

Re: Freezing wood?

#7

Re: shelves for  a fridge

Edward in Vancouver

>MMmmm. White oak, Doug Fir, and marine ply all sound like good choices. Teak and mahagony sound great, but-tum....ah, a bit pricey for the project.

Q: If I were touse marine grde ply and gaiv it an epoxy finish, would I have to cover the edges with solid wood?

Epoxy glue...Never used it yet, but about time I should. Never thought of it.

Finish: Yes, I've got the Flexner book. After dealing with health inspectors for over 25 years in 3 countries, I kind of know what to expect: They don't really care about the finish per say, but what they care about is when the finish fails: When it does, it flakes and invariably falls into food. I figure I've got about a half year before all of my wire shelve's plastic coating fails, and I don't want the health inspector to tell me to replace it--I'd rather be ahead of him.....

Don't have any experience with epoxy finishes, but if a wood boat can endure the elements with this stuff, I don't see why simple shelves in a fridge can't. Still, if I can get away with a simple oil and wax finish, I 'd rather go this route. The shelves will be subject to daily wear and tear--about as much as a kitchen table in a family of 3 pre-teen boys....

For the time being, I'll sharpen my pencil and get prices on Doug fir, flat sawn wht oak, and marine ply. I should factor in the cost of an epoxy finish too.

Thanks for the help

Regards,

Edward

Re: Freezing wood?

#8

Ellis Walentine

Re: shelves for  a fridge

Ellis Walentine

>Another possible candidate that should be readily available in your area is Alaskan yellow cedar. One of the conglomerates (Weyerhauser? Roseburg?) markets it as "Pacific Coast Cypress," a confusing misnomer probably concocted to get around some law or another. It is light, strong and durable in the sense of standing up to moisture conditions. Its worst drawback might be it's relative softness compared to locust or teak, which could cause a hard film finish to break under constant denting conditions. For abrasion resistance and relative toughness, I'd consider a waterborne polyurethane finish such as those used by flooring contractors.

Ellis

Re: Freezing wood?

#9

One question

Dan Donaldson

>If you build them the way you are suggesting, will that allow enough air circulation in the box to keep the temperature even throughout?

Re: Freezing wood?

#10

Re: One question

Edward in Vancouver

>What I had in mind was a 2-3" wide frame and 3 or 4 vertical members that are the same width--thus giving me a "grid" rather than a flat, solid panel. With this type of a set-up, I should have enough circulation.

Why I really want to build these out of wood is because of the system used to hold the shelves in place:

Each shelf slides into a s/s "U" channel that hooks into 3/8" square notches in the s/s fridge interior. Thus the whole weight of the shelf is supported by about 1/4" of 12 guage s/s on either side of the shelf. Granted, the shelves are cheap plastic coated wire, and when they encounter any significant wieght (couple of jugs of milk?) they sag and bend and then pop out of the "U" channels--making a heck-uva mess.

If I were to make a shelf out of, say 1" thick stock and bore 3/8" round mortises into them, and make a brass or aluminum bolt to fit into these mortises, I could "bolt" the shelf directly into the notches in the fridge interior--thus bypassing the whole lousy s/s "U" channel system. For each shelf I would need 4 "bolts" maybe 3" long to support the shelf, where about 2 3/4" of the bolt is buried into the mortise, and the remaining 1/4" into the 3/8" square s/s notch.

Right now I'm still looking into wood choices. Doug fir sounds reasonable but it does smell when wet. Ipe might be another one, and I'm going to get some prices on that.

Re: Freezing wood?

#11

Abrasive woods

Bob Hackett

>If you decide to use ipe or teak be sure and pick up extra blades for your planer and a saw blade for the TS.

Both woods are very tough on even carbide blades.Be prepared to sharpen hand tools often.

MB

Re: Freezing wood?

#12

Re: One question

darin

>Why not cut the grid out of a appropriately size piece of marine plywood?

The mounting mechanism? However it is to be implemented could surely be done with aluminum brackets or channels attached to the plywood.

Re: Freezing wood?

#13

Re: One question

Edward in Vancouver

>Yes, that's exactly what I as thinking....

However: I'm not all all familiar with marine grade ply. Do I need to face the exposed edges with solid wood?