Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Super Resolution Thermal Imaging Camera

Forged dividers

Posts

Forged dividers

#1

Forged dividers

Nathan

>Hi, I just won an auction for two pairs of forged dividers. They came from an old metalworking shop. One is 29cm (almost 12") and the other is 14cm (almost 6").

I guess the biggest question marks are the weight (comfort of use), plus whether they will hold a setting. They appear to be sharp.

What do you think? Will they be useful?


Re: Forged dividers

#2

Jack Guzman from Maine

Re: Forged dividers

Jack Guzman from Maine

>Depends on what you do. I use mine all the time.I have tiny ones all the way up to 16".---Jack

Re: Forged dividers

#3

Stephen Shepherd

Re: Forged dividers

Stephen Shepherd

>Like Jack, I use mine all the time and always looking for more. They shouldn't be too heavy, they are not that big and if the pivot is loose, wrap some sewing thread around the pivot between the arms, rather than tightening up the rivet with a hammer.

Stephen

Re: Forged dividers

#4

Re: Forged dividers

steve mackay

>I love 'em for repetition, transfer and places you can't get the ruler into. Wich, pretty much, describes my day. Have a 16" forged iron pair all the way down to a stray pair of Dietzgen drafting. Trick is to keep 'em handy. If they are in a drawer somewhere I didn't bother hunting them. Now they hang over the bench and I grab, set and go.

Re: Forged dividers

#5

Re: Forged dividers

Dean Lapinel

>Why the string instead of the usual method of tightening?

Re: Forged dividers

#6

Stephen Shepherd

Re: Forged dividers

Stephen Shepherd

>Dean,

Old iron can be brittle and efforts to tighten the pivot rivet can cause metal failure, I know this from experience. The thread is easy and can be renewed with no problem. Rosin or brewers pitch in the joint will also cause enough resistance to solve loose leg problems.

Stephen

Re: Forged dividers

#7

Re: Forged dividers

Bill Houghton

>I have sometimes found tight joint calipers/dividers to be tricky - since you're adjusting by push/pull, you can spend a lot of time going back and forth between measurements. This may be a matter of practice, though - certainly, I've learned to set the iron on a simple spokeshave (Stanley 51/52) by guess through practice; no reason why it shouldn't work on the dividers.

I like Stephen's thread suggestion - that should provide some friction but without stiffness.

Re: Forged dividers

#8

Thanks

Dean Lapinel

>Ahh- Thanks...understood.

Re: Forged dividers

#9

Re: Forged dividers

Nathan

>Returning to the subject of the forged dividers - I received them in the mail yesterday (they are rather old, obviously made by a blacksmith). If you recall, I was worried they might be loose and I received some helpful suggestions on how to fix that.

However, while usable as-is, the main problem I see now with them is that they are too tight. I figure that will be easily solved with some lubrication, but at certain points in their range of movement they tend to "stick". In other words, the tightness is not uniform throughout the whole range. Any ideas on how to fix that?

Re: Forged dividers

#10

Jack Guzman from Maine

Cleaning

Jack Guzman from Maine

>Assuming they worked smoothly at one time I suggest you treat them with electrolosis to loosen up and remove any small bits of rust.I don't recommend agressive cleaning however. Let the electrolosis work for awhile then scrub using hot water and a green plastic scrubbing pad. Then oil the pivots and move them through their range.Work the screw/screws etc.I use this method for most rusty tools. Others may have better methiods but this works for me.

If you're not familiar with electrolosis,there are a couple articles that will help you in Woodcentral's articles section.---Jack

Re: Forged dividers

#11

Re: Cleaning and rust

Bob Hackett

>Jack,

How does electrolysis compare to a soak in vinegar as far as aggressiveness and is there any fear of loss of parent metal when using electrolysis?I`m aware of the hydrogen embrittlement concerns just wondering if the process may be safer long term than vinegar which is what I`m using now.

I did the electrolysis thing a long time ago and can`t remember why I got away from it.

MB

Re: Forged dividers

#12

Jack Guzman from Maine

Re: Cleaning and rust

Jack Guzman from Maine

>Bob,

I have never used vinegar for rust removal.I used it to age a piece of brass by fuming once but that's a different story.Electrolosis removes no metal. The rust separarates from the metal. Paint or platings will separate if there is rust between them and the metal however.So nickel plating will sometimes fall off. If you reverse the electrodes,that is a different story.Then you will lose metal.---Jack

Re: Forged dividers

#13

Thanks Jack

Bob Hackett

>That`s what I wanted to know.

I`m guessing the brittleness thing or maybe just that my old battery charger quit is why I stopped using electrolysis.

Just picked up another charger at the dump so I was thinking about it again.I like to hit things(even rusty things) with the smallest stick possible.

MB

Re: Forged dividers

#14

Evapo-Rust....etc.

Marv

>Nathen,

I've have good luck using Evapo-Rust.

Just soak your tool in it for a few hours and the rust goes away. It will leave a black substance inplace of the rust, but it is easily brushed off. The stuff is a bit pricey though.

Google Evapo-Rust so you can find where to buy it. I think Enco carries it in quart size.

As Bob suggests Vinegar is not a bad thing to try. It's cheap and easy to come by, but use the white distilled kind. Be careful with it though, it can discolor the metal if you leave the tool soak too long and it will cause pitting also. So soak it for an hour at a time, then clean it in water and wipe it dry.

Another thing that might work to make the parts move smoothly is to work a little grinding compound with a light oil into the joint. Work the tool until it moves better then flush out the grinding compound with more light oil.

Another thing to try is graphite. Locksmiths use it to loosen locks and make them work smoother. Sometimes you can find it in liquid form. I used to use it to make my lever cables work smoothly on my motorcycles. I'd squirt in the top end and it would quickly make its way down the cable and out the other end. This stuff works like magic if you can find it.

Marv

Re: Forged dividers

#15

Re: Forged dividers

Todd Hughes

I'd spray it with some WD40 then put it on a fine wire wheel to clean it up some.

If still sticks spray it again and put one leg in your vise while you work the other one back and forth.

If that doesn't work heat it up with a propane torch and spray some oil on it as you work the leg back and forth

If that doesn't work toss it out the window, .....Todd