Coupla details--LONG
Wiley Horne--So. Calif.
>Hi Wilbur and all,
Wilbur asked about handling a Japanese hammer, without a wedge. It's low-tech stuff. Short version: you bash a slightly oversize handle through the eye of the hammer, and never mind the wedge.
Longer version: Just like it takes a bench to make a bench, it takes a hammer to handle a hammer, so it helps to have a decent-size bashing tool with enough momentum so that you don't have to use a lot of head speed to persuade the handle as it moves millimeter by millimeter. Also have a card scraper on hand.
The other preliminary is to be aware that the eye of the hammer has shape. They are slightly restricted toward the center of the eye, from a few thousandths to several thousandths. I like to mic them before I start, to know how tight the restriction is. You want the handle to be tight on the inlet side, tight in the middle, and tight on the outlet side--but how can that be if there is a restriction in the middle??
The key is to take your time. Allow a few days for the fitting. More on this below. Start with a handle blank of wood that is tough but compressible and resilient. All the usual handling woods are good--I've used a So. American version of osage orange (hedge), white oak, and even satinwood, though the latter is probably not the best choice. Am sure hickory is great for the purpose. And ash. Or one of the locusts. Any known handle wood. My favorite is Japanese white oak (kashi), which is a live oak.
By the way, it will occur to you: Wonder if I'm going to blow out the cheeks of the hammer, driving this handle through. You won't. The handle will just absolutely stall in the eye before that happens. Now what if the handle blank is a bit too oversize to drive further, and it just stalls in the eye. You can back out the handle that you've started driving, by punching it out from the top side. But what I recommend if the fit is close, is to take a card scraper, and scrape just below the hammer. You will leave a little ring of fuzz just below the hammer, but that will shear off on the next hammer blow. Scrape off just enough that the handle will move once again.
You don't want a shoulder on the hammer handle below the hammer. Just look at any of the commercial handles for a Japanese hammer. They'll be maybe a foot long. The business end of the handle blank will be a smooth taper for about 3 inches or so. Take a spoke shave and shape the insertion end so that there is a a very gentle expanding taper--for example, if the point of insertion measures, say, 3/8" x 1", then shave the taper so that it expands to, say, 1/64" oversize over a three-inch taper. I'm making this sound more quantitative than it really is, in an effort not to be abstract. I like to make the insertion end a tight, ever-so-slightly oversize fit, and then lightly rasp the very end so it will start. Some extra length is good, so that if and when you mung up the driving end, that'll be gone when you cut to final size.
You're going to drive the handle blank right through the restriction, and let it expand on the other side, the exit side. This may take a while, and experts like So Yamashita will proceed a couple of millimeters per day once the handle has reached the restriction, and pour a little oil into the 'cup' above the restriction, so that the insertion end grain can drink up the oil and expand. Just mark off a string of 1/8" marks below the hammer, once the handle has gotten as far as the restriction. And every day, hammer it down one mark--1/8". This is assuming a pretty tight restriction--several thousandths. You can make faster progress if the restriction is more slight.
What do you hammer on? You want to hammer on an absolutely dead place--so the blows are going straight to ground. That's why I like a tree stump, or rock on the ground, better than anything else. You can do it on your bench, right over a leg, if the leverage is right. But you want the driving end of the hammer no higher than waist high, so you have gravity on your side and a good angle.
I'm making this sound like more of a chore than it really is. I enjoy it a lot. And when you're done, the hammer will not even think about moving on the handle.
Wiley