Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Want Better Milling & Firewood Knowledge?

Onto the last lap for the drawer

Posts

Onto the last lap for the drawer

#1

Onto the last lap for the drawer

Derek Cohen (in Perth, Australia)

>I had a couple of hours after work today and got into the workshop. Just in case there is any idea that my shop is the show piece in my reviews ...


That has been a lot of shavings to create when the temperature has been over a 100 F for the last week or so.

Anyway, onto the slips and the drawer bottom. The slips are going onto three sides. The fourth is where the panel slides in (and so screwed). The Kauri panel is a little over 5/16" thick and feels pretty stiff, so I have decided to go without a dividing mullon (there is still time to change this, so tell me if you believe otherwise).

Fitting the slips:

This Stanley mitrebox does a great job ..



.. and then the ends are shot, more to trim to length than for a finish ..


Here is the first piece inserted ..


.. and the other sides are the same as this ..


Now at this stage I ran out of time, so the drawer bottom was not sized for insertion. This is what I have (and why I write earlier that I can still add a mullon should I choose - I will next get to the workshop on the weekend).


On the other hand I did get to plane down the sides of the drawer - everyone wants to see The Dovetails! :)


For drawers I fit the front and rear faces to the drawer opening, so these dimensions must not change. The side panels are purposely a little proud and need to be planed flush to the sides.

I love it when the dovetails start to acquire a definition ..


The rear through dovetails ...


.. and the front half-blind dovetails (they are spaced to match the dovetail spacing at the top of the cabinet) ..


Regards from Perth

Derek

Re: Onto the last lap for the drawer

#2

Nice work

Bill Houghton, Sebastopol, CA

>I suppose you could test the drawer before final finishing by installing the bottom and putting in a typical load. I assume this is more likely to be sweaters and other such clothes than part of Todd Hughes' anvil collection, so the thin bottom might well serve.

Re: Onto the last lap for the drawer

#3

comment on dovetails

Bill Tindall

>I don't mean this as a criticism of your work. When you are working for your self any amount of effort is fine. Rather, it is information for others that might be building drawers and be more pressed for time. (Anyone with that amount of shavings on the floor is not pressed for time or they would own a planer!) What I was taught (by someone making a living making furniture) was that there is no load on the back of a drawer,and it is never seen. Its only function is to hold the sides together. Therefore, the drawer back can have few dovetails, widely spaced. Also, the drawer back is lower in height than the drawer sides so that there is no risk of it binding over time.

Re: Onto the last lap for the drawer

#4

The other reason for the drawer back being lower

Andrew F in Australia

>Hi Bill,

The other reason that the drawer back is cut lower than the side is to give the air somewhere to go as you close/open the drawer. With the drawer well fitted, and IF the back was the same height as the front, you'd have a devil of a time opening and closing the drawer.

I suppose it would be a 'hydraulic' action drawer closing device, however.

Cheers,

Andrew

Re: Onto the last lap for the drawer

#5

Re: Onto the last lap for the drawer

Andrew F in Australia

>Hi Derek,

The drawer looks good - I'd be happy with it, with the differences in height between front and back as highlighted by Bill.

I read Richard Jones' comments on the slips and can't add to that - if you've got time, I'd re-make the slips to fit a groove cut into the back of the drawer front. I wouldn't mitre the slips, but locate them firmly to the drawer - if your front drawer slip dropped ever so slightly (under load,) then the drawer would not close.

The drawer muntin (it's correct term) would be something that I'd add.

(mullions are the bars that separate window glazing - more an architectural term.) I noticed on the australian WW site that our resident furniture restorer said that Georgian furniture did not use muntins, but fielded the drawer bottom to fit, stiffening it up through it's added thickness. Either way is perfectly OK - if the drawer base is almost rigid, remember that you've got the screws holding it up into the drawer back to supply extra support.

Cheers,

Andrew

Re: Onto the last lap for the drawer

#6

Piston fit drawers

Victor Parisian

>A bit has been written about piston fit drawers. Close the bottom drawer and the top drawer pops out a bit. Allow enough clearance so that you get the piston fit feel without the hydraulic (or should that be pneumatic) closer. Tongue firmly planted in cheek.

Derek that is beautiful. I should live long enough to do such nice work.

Regards,

Victor - on a sunny and warm January day in Houston.

Re: Onto the last lap for the drawer

#7

Opinions needed

Derek Cohen (in Perth, Australia)

>Although the armoire was incomplete when the family came to stay for a week, I moved it into the guest bedroom so that the hanging facility could be used. Since then I have noted that the doors have expanded/swollen by about 1/16". This is enough to prevent them closing without significant force ..

Not a great blow up, but ...


The reason for this is obvious - the workshop is very dry (we have 100F dry heat in summer), while the guest bedroom is bathed in cool air from ducted evaporative airconditioning. The wood was in a dry environment and has had 10 days in a cool (moist-ish) climate.

I have brought the drawer indoors and can see that it is now about 1/32" too wide for the drawer opening. That reflects the amount the wood at the sides of the opening have swollen. It is not much, and this amount is easily planed, however I expect the drawer to "adjust" in the same way as the cabinet, and if I fitted it now it will swell in the cabinet. So I reckon I need to wait a week for all pieces to settle before final planing/fitting.

What do you think?

The other issue is choosing the door and drawer handles. This has proved to be very difficult. It is so because of the inlayed diamond. The temptation is to try and use this as a theme, and fit "diamond-like" handles.

I made up a bunch of options in wood (both Jarrah and Tasmanian Oak) and tried them all - diamond, half diamonds, round, vertical long ... they all just did not work for me.

So here is another option. I like them, but do they work for you? They are brass and have a more vintage look to my eye. These will go on the drawers as well - in line with the diamond inlays.

What do you think?



Thanks for your input.

Regards from Perth

Derek

Re: Onto the last lap for the drawer

#8

Re: Opinions needed

Pam Niedermayer, Austin, TX

>Personal preference: I don't much care to use small loops for opening cabinet doors as they take too much attention to open. Large, almost hand sized loops are OK. The best IMO are carved out of the doors on the top (if the doors will be below waist height) or bottom (if the bottom of the doors is about shoulder height). Then I'd make a couple of wooden pulls, or maybe carved out sections in the inner stiles, to accommodate those inbetween.

Pam

Re: Onto the last lap for the drawer

#9

Re: Opinions needed

Bob Hackett

>I would think it would be a very good idea to let things adjust to the environment they will live in and then fit them.How does you wife feel about shavings and sawdust in the guest room?

I have a friend who spent a rather large sum on a beautiful,mint condition antique curly maple drop leaf table.He brought it home from the rather drafty antique shop where only the front desk area was heated during business hours.After placing it in the heated(central forced hot air)dining room he actually heard it crack and was heartbroken to see the top and one leaf had split.

I don`t know if I like the ring type pulls or not but the idea for brass pulls seems good as it makes the exposed brass of the hinges look like something planned rather than put there strictly out of necessity.

MB

Re: Onto the last lap for the drawer

#10

drawer fitting

Bill Tindall

>I fit the drawers in the Chester county chest I built last year and went on vacation. While on vacation we went from low humidity winter to wet spring. When I returned from vacation I had to drive the drawers out with a large hammer. Fortunately the chest back was not on yet and nothing broke. Before I got everything done I had to refit one more time. The problem was in the height and I was using rift cut poplar which should have been as good as it gets for sides. I had tried to make them too tight to minimized tipping down when opening and that was a mistake.