Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Reach the woodworkers who ACTUALLY BUY

Workbench finished

Posts

Workbench finished

#1

Workbench finished

Haakon Haraldsen

>Hello Everyone,

just wanted to share with all of you some pictures of my workbench just finshed this weekend. I have been working on it on and off for some five years now, and finally it's all done (well, nearly all).

The bench is built in European steamed red beech and follows almost to the letter the Klausz bench described in Scott Landis' "The Workbench Book". However, some deviations can be found such as through dovetails on the backrail. They are easier to do, but also nicer to watch, specially since the bench is tight up aginst the wall.

I'm not very happy about the plywood for the tool well so I'd like to get some half inch beech boards to glue up and redo that paricular part of the bench.

The bench is built mostly using hand tools, a band saw and powerdrill. I did user a planer at some point, but after an accident I decided against it.

The finish is boiled linseed oil.

More pictures in the next message.

Regards

Haakon


img

Re: Workbench finished

#2

Workbench finished

Haakon Haraldsen

>The tail vise


img

Re: Workbench finished

#3

Workbench finished

Haakon Haraldsen

>Tail end


img

Re: Workbench finished

#4

Re: Workbench finished

Haakon Haraldsen

>Shoulder vise end


img

Re: Workbench finished

#5

Re: Workbench finished

Ace Karner

>Very nice! a friend of mine built this bench years ago and I can tell you it is a real pleasure to work on.

Re: Workbench finished

#6

Good on ya

Bill Houghton, Sebastopol, CA

>A nice goal to have met, and a beautiful bench.

Re: Workbench finished

#7

Re: Workbench finished

Hank Knight

>Haakon,

Wonderful bench! I thought long and hard about building Klaus's bench, but I built one of my own design. I don't regret it, but I still think about building Klaus's bench. You did a great job with it. Use it well and enjoy it.

Hank

Re: Workbench finished

#8

Finally someone who works slower than me

GolfSteve in Calgary

>Beautiful bench. You won't regret spending the time buiding that bench.

Cheers,

Steven

Re: Workbench finished

#9

Re: Finally someone who works slower than me

Haakon Haraldsen

>Steven,

Yes, I work to slow, I admit, but the main things slowing you down is not the work itself, it's all those things that prevent you from working on your projects. I'm sure you know what I mean.

Cheers

Haakon

Re: Workbench finished

#10

Fine looking bench!

Scott Burr in Ben Lomond CA

>I think you'll enjoy it for years to come.

Scott, wondering about all those LN boxes...

Re: Workbench finished

#11

what is your first project? question....

Bill Tindall

>Find looking bench. Looks better than my furniture. What will be the first project to christen it?

I have seen the European steamed beech at IWF but have never worked any. How does it compare to maple, birch, etc. in terms of ease of working?

Re: Workbench finished

#12

Re: Workbench finished

charlie belden

>I thought I'd procrastinated building a bench - a year to complete. At five years - you've well exceeded that

No Flip Stop or little swing out Oil Cup?

Are you finding that the screw length of the shoulder vise is too long and gets in the way?

Did you do a sliding "door" in the bottom of the tool tray for getting the stuff that accumulates in it out easier?

Is the end of the bench top frame connected to the bench top with a lag screw - or a barrel bolt in the bench and lag bolt through the "frame"into the barrell bolt?

Did you spline the top's "frame" to the top's core?

I wonder, if Frank Klausz were to build another workbench - would he go with a Veritas Twin Screw Vise on the end?

Nice work on the bench. Now it needs its first ding or scratch and it'll go from a piece of furniture - to a tool - you'll use often - and enjoy.

Re: Workbench finished

#13

Re: Workbench finished

Glenn Madsen near San Francisco

>That's a fine piece of work you have there, sir! Well done!

A few summers back, a group of our woodworkers' club got together and built 9 of those benches, one for the classroom, 8 for others of the team. I've worked on a couple of those, and found them wonderful. My simpler bench, I have a challenge keeping clean.

Your name is similar to that of my grandfathers' people, Danes, your English proper, and your address Italian. Where is home?

Re: Workbench finished

#14

Re: Workbench finished

Wiley Horne--So. Calif.

>Haakon,

Congratulations!! It is a magnificent piece of work which will be admired by your children and grandchildren.

Please stay in touch as to what you will do upon this bench. I might suggest a shooting board as a first project, if you don't already have one. But no matter, now is the time to enjoy the fact that all the hard work has paid off!

The joinery is very beautiful and meticulous throughout, on this bench.

Wiley

Re: Workbench finished

#15

Re: what is your first project? question....

Haakon Haraldsen

>Bill,

Thanks. Yes I'm very happy with the bench, but you can get obsessed with it, and you have to remember as my wife pointed out to me several times during this project; it's only a workbench, not furniture.

The first project is going to be a small cabinet to hold my tv equipment under the tv. It is going to house quite a few pieces, so the design is going to be challenging because I want something that looks very light. I might try mahogany, nerver worked with that, or cherry.

Next project? Probably a small tool cabinet on the wall behind the bench. However, I did some kitchen cabinet doors on the bench just after the top was finished, so I guess it's been christed already.

European beech is very nice to work with. It is hard, quite dense and fine grained. I have never worked with maple; compared to birch it is more of a straight grained wood so it is much more forgiving with hand planes. I'd say it is similar to cheery when comes to working with handtools: it has a nice smell when you expose the wood and it can be planed to a great finish but cheery splits more easily. However, in terms of beauty it cannot be compared to cherry. That is also refleceted in it's cost. Here in Italy beech is less than half the price of cherry.

Haakon

Re: Workbench finished

#16

Re: Workbench finished

Haakon Haraldsen

>Hello Charlie,

you picked the right word - procrastinate. I was on and off for about 5 years, but that's elapsed time. The whole project was done in three major spurts:

- Base 3 months

- Top and shoulder vise 3 months

- Tail vise, end caps and tool tray 2 months

So all in all about 8 months during which I worked most evenings and weekends.

I said it is nearly finished, so the flip stop is still missing, but I'm not going to add the oil cup. I prefer to keep oil in a separate bottle somewhere on a shelf.

The shoulder vise screw do sometimes get in the way, but that's more because my work area is too small; I am relegated to the bottom of the garage with a lot of junk I probably should have thrown out before starting the bench. When cutting dovetails or tenons this is the best vise you can get (my opinion), but of course it is not as strong as a Record.

I did put in a single piece of plywood for the tool tray bottom. It is temporary, as I want to replace it with some solid half inch beech planks with ramps at the extremes. When I do that I will put in a sliding door but not so much for cleaning out the well, but rather to be able to clamp things to the bench top at the back. I saw that in "The Workbench Book" page 98. Looks cool.

The end caps are connected to the top using lag screws in addition to being glued for about half the benchtop width. In addtion there is the 1/2 inch threaded rod that goes from the shoulder vise all up to the tool well.

Yes, the the frame was splined to the top's core using 1/2 plywood strips.

I have never met Frank, but my gut feeling is that he would stick to this design.

Thanks. I dread the first ding or scratch, but the sooner the better, because too much care for the bench slows you down.

Cheers

Haakon

Re: Workbench finished

#17

Re: Workbench finished

Haakon Haraldsen

>Thank you. It is very nice to work on, only it is a tad slippery, but I think I'll get used to it.

Your last name cetainly sounds Danish. I grew up in Norway (where English is widely spoken), but I have lived in Italy most of my adult life, hence the address. Home is by now in Italy where I live with my family near to the city of Parma.

Cheers

Haakon

Re: Workbench finished

#18

Re: Workbench finished

Haakon Haraldsen

>Hello Wiley,

thanks. Admired I don't know, but I hope they will use and enjoy it.

I will make a shooting board and a cuople of bench hooks for cross cutting. I'm not totally conviced that the flip stop (when I get around to that) will work for wider boards.

The joinery is acceptable. The tenons in the base came along well form the start. The dovetails less so. I cut my first real dovetails (ie not on scrap) on this bench. The first, at the shoulder wise, was really bad and that had to be repaired with shims. You can see that in one of the pictures. I also had to throw away one of the jaws in the tail vise, but all in all the tail vise came along quite well so I guess practice makes master. Certainly I feel more confident now going about joinery.

Cheers

Haakon

Re: Workbench finished

#19

A question about olive wood

Bill Tindall

>Thank you for the information about your beech. It is imported into the US in small quantities. Our north American beech in not an imortant lumber species for various reasons.

Having never seen an olive tree I don't know how they grow or whether they would be able to yield larger boards. I can buy small pieces of olive wood that are used to turn small objects from. It can be a beautiful wood. Is olive wood available to you in boards large enough to build furniture and cabinets?

Re: Workbench finished

#20

Re: Workbench finished

wilbur

>That's a gorgeous looking bench! Thanks for posting it for two reasons:

1. Inspiring me to get going and finally finish my workbench, and

B. making me feel not so bad about the fact that it's been over a year when I first started on mine. :@)

What are the dimensions of your bench, and how did you settle on the final dimensions?

Re: Workbench finished

#21

Re: Workbench finished

Haakon Haraldsen

>Wilbur,

the dimensions are roughly as follows:

- Overall depth at the shoulder vise 37 1/4 inches

- Overall depth at the tail vise (from backrail to front) 26 1/4 inches

- Overall depth at the tail vise of the main top 18 inches

- Overall width (end cap to end cap) 78 1/4 inches

- Height 36 inches

The top dimensions are pretty much in line with what is described in Landis' book. Deviations were mainly due to dodgy conversions of imperial measures to metric and the size of boards I ended up with.

The hight on the other hand was increased by some three inches. I didn't really know what height I wanted when I started so I figured that it was better to make it on the high side; easier to add an inch or two the floor with a floor board rather than having to raise the bench.

Turned out that the hight is just right for what I do, a mix of handwork from planing to sawing joinery. I'm 6 ft 2 inches.

Good luck with your bench. It is really rewarding the day you put a piece of wood between the dogs and you say "How did I ever do without?"

Haakon

Re: Workbench finished

#22

Re: A question about olive wood

Haakon Haraldsen

>Bill,

I have never seen olive tree wood in the lumber yard, but I live in the North of Italy where the only olive trees you see are ornamental trees in people's gardens or in parks. Down south it is a very common tree and it is part of the agricultural landscape.

I would be surprised if you found straight lumber longer than 4 feet and even that appears to me to be on the long side judging from the trees you see out there.

The wood itself is said to be of execeptional figure and very hard. It is often seen in wooden floors in this country. But again, very short pieces.

I will send you a link to a company I found that provides Olive tree lumber.

Haakon