Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Veritas - Innovation in Tools

Hats off to the pros among us ...

Posts

Hats off to the pros among us ...

#1

Hats off to the pros among us ...

Derek Cohen (in Perth, Australia)

>This wardrobe/armoire project has confirmed that I would make a poor professional. I just can't work fast enough!

This piece was intended for a small guest bedroom, in time for a week's visit on the part of my wifes brother and family. Well they arrive tomorrow and the armoire is not finished. Rats!

At least it is usable, and I can stop rushing. I hate working like this. Today I built the door handles twice, and I am not happy with them. The first time my wife vetoed them as she did not like that they were in Jarrah and created too strong a contrast (which I liked but I was not happy with the shape), and so I made a new shape, but I am not happy with their thickness (that is easy to change). However I am not so sure I like the Tassie Oak for the handes. Any thoughts?

I also spent my time planing down and thicknessing the boards for the rear of the cabinet. Man, that was hard work on one of the the hottest days for many years in Perth!

Anyway, here is the armoire in the guest room. Not a good picture as the lighting was difficult. As Imentioned, this needed to be a small piece (it is just 51" high without the Jarrah top, which is still to go on), and to provide hanging space and a large drawer (which has been started).

Side view ..


Current status ..


Doors opened ..


You can see, to save space, I have turned the hanging direction around.


Oh well, the room looks nice and Lynndy is happy. Can't ask for more than than.

Regards from Perth

Derek

Re: Hats off to the pros among us ...

#2

If Momma is happy . . .

steve mackay

>EVERYBODY is happy ! Neat stuff !

Re: Hats off to the pros among us ...

#3

Hats off to you

Bill Houghton, Sebastopol, CA

>Derek,

You feel bad about stuff I'd be proudly picturing in my holiday newsletter!

One door pull question: is there plenty of room between pulls for fingers? From here, they look pretty close together, but my perspective may be distorted by the 14,000 or so miles* between us.

*(side note: not knowing the distance, I looked up directions on Google Maps - I was informed that public transit wasn't available, so asked for driving directions, which had me drive from here to the top of Washington State, kayak to Hawai'i, drive across Hawai'i [in the kayak, apparently - no reference to renting a car], kayak to Japan, drive across Japan, kayak to Oz, entering at the Northern Territories (city not specified), then drive the kayak to Perth. So the mileage may be a bit off. I just love computers)

Re: Hats off to the pros among us ...

#4

Re: Hats off to the pros among us ...

wilbur

>That looks like a beautiful project!

You may have covered this in the past, but can you comment on how you decided on the dovetail spacing for the carcass?

Re: Hats off to the pros among us ...

#5

Re: Hats off to you *LINK*

KenI

>9148 miles according to Wolfram Alpha. I've only used it a couple of times, but it seems to figure things out pretty well.

And as for the real subject of the thread... I only wish I could produce work like that. I am looking forward to see it's final form.

Ken


alpha results

Re: Hats off to the pros among us ...

#6

wood selection-nice

Bill Tindall

>It is a pleasure to see something made where the wood was selected and assembled to enhance the design. I agree on the current wood selection for the knobs as well as the thought of thinning them. I would have located them higher, but that is a personal choice.

Perhaps you described this detail earlier and I missed it. Is there any profile on the inside edge of the frame and if so how did you do the joint where the molded stile meets the rail? If the inside edge is orthogonal then ignore the question.

Some of us face deadlines on making stuff most of the time. This project may provide more appreciation why those working with deadlines own thickness planers, mortise machines and jointers. The final result will look the same but take less shop time enabling one to get on with making the next piece.

The thought of sweating is remote. We are in the midst of the most prolonged cold wave since the 1970's.

Re: Hats off to the pros among us ...

#7

Re: Hats off to the pros among us ...

Thomas Skaggs, Foothills of Mount Level

>Just remember, it's not the pace of the journey that matters. As long as you take time to enjoy yourself along the way. And with this piece it certainly looks like it was a nice journey indeed.

Tom

Re: Hats off to the pros among us ...

#8

Lookng good!

Scott Burr in Ben Lomond CA

>Better off not to rush it, that just leads to trouble. DAMHIKT!

Let 'em live out of a suitcase this trip. Next time, they will enjoy your spoils even more.

Re: Hats off to the pros among us ...

#9

I would be tempted

Bill Houghton, Sebastopol, CA

>to buy some stuffed monsters of some kind to put in the space where the drawer will be.