Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Urban Salvaged Hardwood Slabs, Milled In-House from Rare Trees. Shop Unique Walnut Stock.

There should be a warning ...

Posts

There should be a warning ...

#1

There should be a warning ...

Derek Cohen (in Perth, Australia)

>... on the side of all rebate planes, especially skew rebate planes.

I cannot recall a time that I have finished a planing session without cutting all my fingers. This is near the end of today ...


The problem is that I prefer to push the fence against the edge of the board rather than hold the knob (which is safely out of harm's way). My fingers are close to the blade. When it comes to skew blades, I forget that they extend further back (than in line with where I think they end), and so I inevitably slice a finger tip! This is not confined to skew rebates, however. I do it on all rebate planes!

Here are a few illustrations. I was making rebates and raised panels.

No, I am not left handed - the grain just went that way ...


See here ..


So how do you hold a rebate plane?

Here is an update of the wardrobe I am building. The doors are a dry fit. Tomorrow I will drawbore the mortice and tenons, fit the hinges, set the inlay, and fix the face frame. Then it's the drawer, top and base.

It's good to have a week's grace before my wife's family descend on us. This piece is needed for a guest room.


Regards from Perth

Derek

Re: There should be a warning ...

#2

Re: There should be a warning ...

Ted

>Derek,

I hold mine the same way that you do and I always seem to cut my finger tips. I figure it just goes with the territory...

Ted

Re: There should be a warning ...

#3

Be proactive...

Bob Hackett

>Take Red Green`s advice and reach for the duct tape.

Tape up the finger tips B4 the planing takes place and you`ll get less "organic red stain" on the work and tools.

Now if I could just remember to heed my own advice.:^)

MB

Re: There should be a warning ...

#4

Re: There should be a warning ...

Alexander Grigoriev

>Derek,

Get some thin brass sheet and fashion a guard (cover) to the fence and the plane body. If anything, adhesive HVAC (aluminum) tape can be used directly on the plane body.

Re: There should be a warning ...

#5

There should be a warning ...

R.J.Whelan - Sierras, California

>Derek ... maybe you should just put the bandages on in advance ... rj

Re: There should be a warning ...

#6

Use the protective tape that...

Scott Burr in Ben Lomond CA

>A lot of assemblers use. It's has a gauze type material with a light adhesive on it. Generally green or pink in color. Just wrap you fingers before starting planing.

Re: There should be a warning ...

#7

Re: There should be a warning ...

Andrew F in Australia

>Hi Derek,

Looks good.

Just noticed something that you might benefit from if you haven't done so already. It looks as though you haven't glued the carcase up yet - in trade, we make/glue up the frame before fitting drawers and doors, just in case it's out by a mm or so.

I trust that the fires have had no impact on you personally or those you know, aside from the smoke.

Cheers,

Andrew

Re: There should be a warning ...

#8

Re: There should be a warning ...

Nick Tuzzolino

>Too bad you don't live in California. You could sue the plane maker and the blade maker. Probably the delivery company, too.

Re: There should be a warning ...

#9

Re: Be proactive...

Tony Z.

>Glad to see another member of the Possum Lodge here!

Re: There should be a warning ...

#10

Re: There should be a warning ...

Derek Cohen (in Perth, Australia)

>Hi Andrew

No fires in my area, but we know how bad they have been elsewhere. Still, the weather has been HOT, around 100F, and it has been hard to spend long periods in the workshop (I could do with aircon).

The carcase is through dovetailed at the top with two sliding dovetailed panels. That was completed and glued. However the doors are and side frames are loose. My plan is to drawbore the doors today, hang them, and only then attach the side face frames to the carcase. I have allowed a little fudge factor for the frames. That way I get a good fit for the doors.

I think I am going to take time to tape my fingers before I use open rebate planes in future. It is not just this plane - I do it on all the onew with open sides - the eye goes to the side closest to you, and forgets the other side of the plane ... just where your fingers are! The worst was my Record #778 - that plane is LETHAL! Anyway, what are a few drops in a good cause? :)

Hope you are well - any fires your way?.

Best wishes for 2010.

Regards from Perth

Derek

Re: There should be a warning ...

#11

Re: There should be a warning ...

Andrew F in Australia

>Hi Derek,

New Year's morning here and all is quiet (eerily so!) No traffic on the freeway, nothing at all happening in the street, nada, nix, nothing.

The explanation makes sense - normally we make doors about a mm or so bigger so that you can plane them down to fit an out of square carcase. More than one way to skin a cat, however.

No fires this side, it's more the 'flood' part, just waiting for the pestilence to complete the trilogy. The rain's made a pleasant change.

I can sympathise with working without air conditioning. I have to work with a few sweatbands on my forehead a'la a ninja warrior, I just rotate them and they dry out before it's their time again in the high heat.

Wishing you all the best for 2010.

Andrew F

Re: There should be a warning ...

#12

Brings back memories..

Roninkokomo

>Glad to see someone else has these issues. Back ten years ago when I was a frequent poster on "the porch" O'deen nicknamed me

"the Bleeder"

I thought that was cruel and showed a certain lack of brotherly concern, even if it was true. My worst one was while trimming a mortise with my 3/4 inch Chas Buck paring chisel which was like a razor and the stile disintegrated and the chisel went to the bone on my little finger,which of course was in the wrong place. 14 stitches IIRC.

Re: There should be a warning ...

#13

Looks like my fingers...

John in NM

>After a week at work in the winter (I work at 10,400' elevation at a telescope). Only mine are just dry and split.

With one exception, all my hand/finger injuries have come from hand tools, usually chisels.

Get one of those kevlar carver's gloves maybe? You could be the Micheal Jackson of woodworking (one glove you see).

Re: There should be a warning ...

#14

Re: There should be a warning ...

VT_Andy

>Derek,

You've got to change something about the way you are doing that! Or at least put a rubber guard on your fingers when using that plane.

Yikes.

-Andy

Re: There should be a warning ...

#15

There is a simple solution ...

Derek Cohen (in Perth, Australia)

>... all one needs to do is add a thickish sub-fence.



What this does to prevent wayward fingers getting close to the corner of the blade. It helps, however, if you have the longer rods (as I recently purchased .. more later).


This is an issue found on the Record #778 as well. Here is an un sub-fenced fence ..


Interestingly, by chance or good design, the Stanley #78, with its single arm fence, actually covers the edge of the blade...


Regards from Perth

Derek

Re: There should be a warning ...

#16

Re: There is a simple solution ...

Stuart Hough

>I've always heard that it's mot really handmade unless it's got you blood, sweat and tears in it!

Re: There should be a warning ...

#17

Re: There should be a warning ...

dave jeske

>Derek,

My fingers often look like that also. I hope that none of my tools ever get used as a murder weapon because my DNA is all over them!

Dave