Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Precision you can feel — woodworking perfected with Lee Valley

"Waxing" plane soles

Posts

"Waxing" plane soles

#1

"Waxing" plane soles

Doug Reynolds in Seattle

>I have always used some form of bees wax to wax the soles of my hand planes. Right now I carry a piece of wax from a beehive in my apron. I recently heard I should be using paraffin instead. I don't know what the difference is between the two or, that it really makes a difference which I use given that I am a casual hobbysit. Any opinion?

Re: "Waxing" plane soles

#2

Re: "Waxing" plane soles

Bruce, a MN Galoot

>I use paraffin myself, as I thought beeswax was too sticky.

Re: "Waxing" plane soles

#3

Re: "Waxing" plane soles

brian greene

>I've been waxing the soles of my planes with paraffin for about 25 years. Just a squiggle reduces friction dramatically. I have read that beeswax is stickier. Paraffin seems quite clean and I've experienced no finishing problems.

Re: "Waxing" plane soles

#4

Stephen Shepherd

Re: "Waxing" plane soles

Stephen Shepherd

>Doug,

Don't listen to people who tell you to use paraffin, especially if you are happy using beeswax. I use beeswax for a variety of purposes, lubricating nails and screws among other things. My grease cup contains 75% beeswax, 25% tallow mixture. Works great on antique drawer runners, whereas paraffin would be inappropriate.

Beeswax is a natural product that is renewable and smells good when you use it. Paraffin is a petroleum distillate and not so green, if that matters.

If the beeswax is too sticky, just heat it up and the remaining honey will evaporate.

Stephen

Re: "Waxing" plane soles

#5

Whatever works

David Miller from Iowa

>I believe this issue to be one of the many where it really doesn't matter much, stay with what you are used to.

Personally, I don't use any lubricant and it is hard for me to believe that minute variations in the coefficient of friction of the plane sole makes a material difference when considering all the primary variables (i.e., wood properties, grain direction, cutter sharpness, plane tuning, technique, etc.)

Re: "Waxing" plane soles

#6

Re: Whatever works

Ted

>David,

I recommend that you try some lubricant, paraffin or other wax. Just get an old candle and scribble on the sole of the plane. I think you will be surprised at the difference it can make.

Ted

Re: "Waxing" plane soles

#8

Re: Whatever works

Alexander Grigoriev

>Never used lubrication? Makes A LOT of difference on end grain.

Re: "Waxing" plane soles

#9

Re: "Waxing" plane soles

Bill Houghton, Sebastopol, CA

>I see no reason why beeswax wouldn't work fine.

I use furniture paste wax and wax the sole periodically, as if waxing a finish. This lasts for weeks for my (sigh!) occasional use, and protects the sole from the rust gremlins too.

Re: "Waxing" plane soles

#10

scott grandstaff

Re: "Waxing" plane soles

scott grandstaff

>If you have never tried it, you owe yourself a run.

Grab a candle or piece of parrifin, or beeswax, whatever, and just squiggle some lines on the sole of your plane ahead and behind the blade.

A few casual squiggles, don't get obsessive on me!

If you have already been planing, watch yourself.

You could well fall forward on your face when the plane whizzes across!

I heard to use beeswax back when I started, but didn't have any. So grabbed a chunk of 59cents a pound parrifin.

Since then, for 30 years a chunk of dirty old parrifin has been handy to my bench, somewhere. I don't use it everyday, its hardly necessary, but for long sessions its just the greatest.

Some guys make a wick of rolled up cloth, felt or leather and packed tight into a small tin.

Then soak the whole maryanne with a copious amount of oil and draw a plane back across that occasionally, for the same reason.

I'm sure this works too.

But always seemed a little fussier than a candle stub in your pocket.

I could easy knock a tin over and spill oil on my otherwise skudgy old concrete shop floor. Not sure about you. heehehehe :)

yours Scott

Re: "Waxing" plane soles

#11

Re: "Waxing" plane soles

ThomD

>A properly designed plane shouldn't need waxing, but we have all probably got a plane that does need a little wax. Bee's wax is perfect for this task. It has extremely high resistance to friction, try it on the fixed center of a wood lathe at high speed. Can be difficult to rub out on the sole, but once on it is long lasting.

Re: "Waxing" plane soles

#12

Re: Whatever works

ThomD

>It isn't a minute variation on some cast iron surfaces. I mostly use wood planes, or buy the bronze version when available. They hardly require lubrication. Or the sole is relieved. On a properly designed plane the difference wouldn't be as large. Just another reason I don't like cast iron for planes.