Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Support WoodCentral when buying things you need

Completed just in time for Christmas!

Posts

Completed just in time for Christmas!

#1

Completed just in time for Christmas!

Derek Cohen (in Perth, Australia)

>This one went down to the wire as I started it late. Got it finished today.

A couple of months ago I found three rather battered Sabatier chef knives - all minus their scales ...


This is how they looked when new ..


These are good quality knives and were not worthy of such an end to their lives.

I had this idea that I could bring them back to life. A little differently (of course - that's where the fun lies. These may be a Christmas gift, but the pleasure is partly in the making).

So I ground away the steel handles (avert your eyes if squeamish)...


Ground away the front bolster for a ferrule ..


.. and turned new handles out of Rock She-oak. This wood has the most amazing fiddleback figure. And this is what appeared ...


I managed to get the knives done last Sunday. Today I built my first knife block out of Jarrah. The finish for both knives and knife block is a little buffing oil followed by Shellawax.




Thanks for sharing this with me.

Merry Christmas all.

Regards from Perth

Derek

Re: Completed just in time for Christmas!

#2

very cool Derek

roninkokomo

>

Re: Completed just in time for Christmas!

#3

Pleasure . . .

steve mackay

>Not just nice tools but I'll bet they are a pleasure to use.

Re: Completed just in time for Christmas!

#4

Beautiful work, Derek, all over the place.

Pam Niedermayer, Austin, TX

>

Re: Completed just in time for Christmas!

#5

Re: Completed just in time for Christmas!

Philip

>Derek,Beautifully done! Merry Christmas, to all Down Under! Phil

Re: Completed just in time for Christmas!

#6

Re: Completed just in time for Christmas!

Victor Parisian

>Very Nice. Up to your usual high standards.

Not dishwasher safe anymore though.

Here's hoping you and yours have a wonderful Christmas.

Victor

Re: Completed just in time for Christmas!

#7

Someone actually using a Zyless vise!

Neal in San Jose

>Way cool! The knives and block are dynamite, too!

Re: Completed just in time for Christmas!

#8

Re: Completed just in time for Christmas!

John Pappas

>Derek, I always appreciate your work, your photography and your detailed descriptions. I'm sure the question on the minds of many here is, "Does this guy ever sleep?" ;-)

Re: Completed just in time for Christmas!

#9

So much to like there, but

Wiley Horne--So. Calif.

>I partiularly like how the knife block 'knifes' into its base. And also the continuing focus on native woods. That she-oak was highly prized for banding in the 18th century, and it's still beautiful wood.

Thanks for sharing!

WIley

Re: Completed just in time for Christmas!

#10

Re: Someone actually using a Zyless vise!

Derek Cohen (in Perth, Australia)

>Hi Neal

I bought that Zyliss vise about 30 years ago. In recent years it has found a niche for holding blades, such as here, as well as saw blades.

Merry Christmas!

Regards from Perth

Derek

Re: Completed just in time for Christmas!

#11

More on She-oak

Derek Cohen (in Perth, Australia)

>Hi Wiley

The particular She-oak used for the knife handles is special. Western Australia is home to some beautiful hardwoods, but this piece used was given to me by Bob, a friend. It is "Rock She-oak", and has a finer and less interlocked grain than the type I usually work.

The typical WA She-oak looks like Lace wood. Here is a box with which you are familiar ..


Now Bob gave a chunk of this Rock She-oak to myself and another friend of ours, Ian. Ian decided to make me an early Christmas present, a dovetail saw (he knows I love joinery), with the Rock She-oak for a handle. I must say that Ian is one very talented sawmaker and this saw cuts oh so sweetly! (for those interested, this is filed 15 tpi rip with 5 degrees of rake and about 5 degrees of fleam).

But it is the wood I want to show off. Here is the saw ..




You can get a better idea of the fiddleback here, but it is still not a patch on the live version.

Very best wishes for Christmas!

Regards from Perth

Derek

Re: Completed just in time for Christmas!

#12

Jesper, Denmark

Re: Completed just in time for Christmas!

Jesper, Denmark

>Nice work, Derek - as usual.

Can you tell a little on how you fit the tangs in the handles?

Re: Completed just in time for Christmas!

#13

Construction details

Derek Cohen (in Perth, Australia)

>Thanks Jesper

Basic stuff, I think. A real mix of hand- and power tools.

The handles were turned and fitted for the ferrules at the same time. I used a template with measurements so that the dimensions remained constant. Then I reversed the handles in the lathe and drilled a hole that would take the tang of the knife. This is standard procedure when adding a tang to a handle.

Poured in epoxy, slid in the tang, and hey presto! The rounded gaps (from a round hole) on the sides of the straight tang are supported by epoxy and are invisible under the ferrule.

The knife block is actually 5 pieces jointed together. Three were rectangular, and two were triangular (I am not sure if the pictures show it, but the block tapers down at both ends and curves across the top). Triangular pieces were glued between the straight sections. To get the mortices for the blades I simply ran three of the rectangular sides across the tablesaw. The kerf was perfect for the blades.

The block was shaped with hand planes, mainly a jack for removing waste fast, and then a smoother, scrapers and finally sanded to 800 (I hang my head in shame - but therounded sides were difficult to smooth just with scrapers) before applying the finish. Block plane on end grain. Fun stuff.

Regards from Perth

Derek

Re: Completed just in time for Christmas!

#14

Re: Someone actually using a Zyless vise!

Neal in San Jose

>That's about how long I've had mine. I have ALL the attachments, even the lathe, that were all picked up at various garage sales from people that generally didn't know what they were. It used to see more action when I was a contractor and working out of a van. Now, I only even think of it about once a year since my bench has good vices.

Re: Completed just in time for Christmas!

#15

Bench vices

Bill Houghton, Sebastopol, CA

>Wine, wenge, and song?

Re: Completed just in time for Christmas!

#16

you're a bad man

Bruce, a MN Galoot

>

Re: Completed just in time for Christmas!

#17

scott grandstaff

Re: Construction details

scott grandstaff

>I thought the bock was particularly fine and elegant Derek.

Imagination and style are seldom brought to a knife block and it warmed me considerable to see this one.

Way to Go!!

yours Scott

Re: Completed just in time for Christmas!

#18

Re: Completed just in time for Christmas!

ThomD

>From the sublime to the ridiculour I saw the attached while Xmas shopping:

http://www.thinkgeek.com/homeoffice/kitchen/86dd/zoom/

Re: Completed just in time for Christmas!

#20

Very nice Derek!

Scott Burr in Ben Lomond CA

>Nice lines to the knifes and the block too. A few questions if you don't mind...

How are the knifes set into their handles?

How is the block assembled together?

Shame the elephant logo was lost. Oh well that's just how it goes.

Again, very nice looking project.

Re: Completed just in time for Christmas!

#21

Re: Very nice Derek!

Derek Cohen (in Perth, Australia)

>Hi Scott

Thanks.

I did post the information that will answer your questions above in "Construction Details".

Hope you had a great Christmas!

Regards from Perth

Derek