Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Good Hope Hardwoods - Walnut Slabs & Specialty Hardwood Lumber

OT- hammer ID

Posts

OT- hammer ID

#1

OT- hammer ID

Bill Houghton, Sebastopol, CA

>This hammer was part of the station toolbox when my dad picked up a gas station across from his car lot in the mid-60s. When Texaco canceled the lease and, with it, his franchise (with one month's notice! The oil companies then weren't very thoughtful toward their franchisees), the rollaway from the station followed him home, and, when we cleaned out the garage a couple of years ago as we prepared to sell the house (Dad had died and Mom had moved to a care home), the rollaway and this hammer, among other tools, followed ME home.

Does anyone know what the original function of this forged steel hammer would have been? It's a great automotive and general purpose bashing hammer, because the compact head gets in tight spaces, but it's fairly heavy for good bashing; but there's part of me that thinks it must have had a more specific purpose in life than general purpose bashing.


img

Re: OT- hammer ID

#2

Re: OT- hammer ID

steve mackay

>I'm probably wrong (often am around here !) but it immediately struck me that I saw these used by locomotive folks to hit the air couplers between rail cars.

Re: OT- hammer ID

#3

That would make sense

Bill Houghton, Sebastopol, CA

>The station was probably less than half a mile from the East Bay (SF Bay) railroad tracks, so it could have migrated from there.

The picture makes it really obvious that the handle's been bent a little. At some point, I guess I'll have to replace it.

Re: OT- hammer ID

#4

Re: OT- hammer ID

Don McConnell

>Bill,

Based on information from Salaman's _Dictionary of Tools_, I think what you have is a Coach Framing Hammer. Alternative names are Double-faced Hammer, Mash or Massie (Scots), Railway Carriage or Wagon Builder's Framing Hammer. I've attached a scan of the illustration below.

The text reads, in part: "A large double-faced Hammer usually with deeply chamfered necks. One of the faces is sometimes domed. The handle is usually short ... . ... These Hammers are used for framing up coaches, railway carriages, carts and wagons, and similar work."

Hope this helps.

Don McConnell

Eureka Springs, AR


img

Re: OT- hammer ID

#5

hammer

paul womack

>Hmm. The variations in hammer design tend to be subtle, but I've seen an awful lot of blacksmith using hammers like that:

The commonest name is "shoe turning hammer", but take a look here and see what you think:

http://www.hammersource.com/Blacksmith_Hammers2.html

BugBear

Re: OT- hammer ID

#6

Correct

Todd Hughes

>Is what is called a "Turning" hammer, have heard them also called "clipping" or "rounding" hammers too. Is the hammer used by Farriers to shape the Horse shoe after it is made, turning or rounding it over the Anvil Horn. One face will be flat and the other slightly domed...is a clasic 'smithing hammer.

...Some of these hammers can be worth some pretty good coin, one of the most expensive hammers I ever sold was a Heller Turning hammer that looked just like the above one, went for around $400 if I remember right,,,,Buyer was going to use it too...or at least thats what he told me

I bought it off a guy who was quite conviced it was a stone hammer and worth $5......Todd

Re: OT- hammer ID

#7

Doubt mine would go for that

Bill Houghton, Sebastopol, CA

>I'm unable to find any markings on it - if there were any, they're hidden under the dents and bruises.

Re: OT- hammer ID

#8

Re: That would make sense

Marv

>Bill,

I have some of my Dad's old tools, one is an old ball pean hammer I remember using myself when I was a kid working in his sawmills. I have so many other hammers, I wouldn't think of using that old ball pean or changing it in any way. It still has the old dark grease obsorbed into the handle. When I pick the hammer up, it's almost as if he is picking it up.

Marv

Re: OT- hammer ID

#9

Re: That would make sense

Wiley Horne--So. Calif.

>Hey Marv,

Your Dad's mills....Were these band mills? Were there circular plate saws there? If there were circular saw plates, did anyone on site tension them, or were they received tensioned?

Where I'm going with this: I am curious about the hammers used for tensioning and flattening saw plates. I'm under the impression that dogs' head hammers were/are used for this.

Wiley

Re: OT- hammer ID

#10

Re: That would make sense

Marv

>Hi Wiley,

My Dad built his own mills. They were portable, mainly stud mills that cut mostly 8 ft. lumber. The mills being small, had only one round blade. If the blade needed retensioning he would always send them to the people who knew how to do that. As a kid I knew nothing about it, but in later years I learned a little. A special hammer is used that has the handle inserted into the hammer head off center. The handle is relatively short so that the end of the handle actually hits the saw plate just as the hammer head hits. The handle hitting the saw plate keeps the face of the hammer hitting flat and not tipped forward too much or backward too much. It's quite an art to hammer a saw plate. It requires an ability to read the surface and know exactly where to hit and how hard to hit.

Marv