Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Rare Exotic & Domestic Hardwoods, Milled In-House in Oregon. Browse Unique Stock.

Grinding a Small Chisel

Posts

Grinding a Small Chisel

#1

scott grandstaff

Grinding a Small Chisel

scott grandstaff

>Just did this.

A friend needed a small (1/4") dovetail chisel for cleaning out small dovetails.





Grabbed a short but heavy, junk firmer chisel (square side originally) out of the drawer and ground a dovetail trimmer out of it.

The extra beef of the blade made it.

yours Scott

Re: Grinding a Small Chisel

#2

Nice! I've modified a few that way myself...

Scott Burr in Ben Lomond CA

>For specific purposes, that is. The funny thing is I needed to adapt some of my Japanese DT chisels the same way. I guess you would call it super-tuning them. Should have came that way to begin with...

Re: Grinding a Small Chisel

#3

Scott, that's an

Wiley Horne--So. Calif.

>incredibly fine and even taper on the side of that chisel! You make it sound like you grabbed it and free-handed it--my hat is off to you whether you free-handed it or jigged it someway. Beautiful job!

Wiley

Re: Grinding a Small Chisel

#4

Re: Japanese chisels

Pam Niedermayer, Austin, TX

>Japanese dovetail chisels are called such because of their shape, not their function.

Pam

Re: Grinding a Small Chisel

#5

How do you get that perfect grind?

Bill Tindall, E.TN

>I have a chisel that looks almost exactly like that except for the wavy grinding.

Re: Grinding a Small Chisel

#6

Re: How do you get that perfect grind?

Derek Cohen (in Perth, Australia)

>Hi Bill

I don't know what Scott did (I'm looking forward to finding out), but a few years ago I did the same. To obtain an even grind, I built a jig that clamped and ran the blade past a grinder wheel. This created a shallow hollow grind through its length.

Regards from Perth

Derek

Re: Grinding a Small Chisel

#7

Well then..

Scott Burr in Ben Lomond CA

>Shouldn't they be called Japanese Triangle Chisels? That is their shape.

Also if that's the case what's their function?

Re: Grinding a Small Chisel

#8

Re: Well then..

Pam Niedermayer, Austin, TX

>Because they usually have small bevels, therefore aren't triangles but five sided. And it's the small bevels that don't allow them to be perfect dovetail chisels.

Pam

Re: Grinding a Small Chisel

#10

scott grandstaff

Re: How do you get that perfect grind?

scott grandstaff

>Hey Hey what wavy grinding??

Its hollow and smooth both sides, meets right in the middle. As If! Sheesh

The bevel runs to the edge at the very tip but tapers toward the top for added strength.

Nope no jig, no nothing. In fact I didn't even have great footing from some assorted mess I didn't get all the way cleaned up. :)

Cheap old grinder, very coarse wheel, 1/2 a coffee can of water for dunking. Took maybe 20 minutes. Maybe a bit more.

Hold the tool in your bare hands. Use the tool rest to rest the backs of your fingers on, so you can feel it at all times.

Keep the blade moving at all times.

You can swing to one side lightly and heavier on the bad side you need to even up, but keep it moving regardless or you'll burn it.

With hollow grinds guys, its a feel. You feel for it.

You take the first pass totally blind, so you try to put it in the middle of where you want to be, and some material removed, but not too deep.

Then lift it free and see what you did.

For the next pass you find the path you made by feel. -Very- lightly address the wheel with your antennae up, and "feel" for it by rocking slightly until you drop into the pocket. You'll find it.

Now dig in and grind, but always moving remember. You can cut some pretty good steel with a coarse wheel as long as you keep it movin.

Now where was it off?? Which side do you need to "lean' against. Its always one or the other. So you lean toward that side without leaving the "trough" you just cut.

Not totally leaning, stay in that pocket, but just a lean will start moving you back to center as you grind.

2 or three more passes and take another look. You can alter the pressure as you go in case the tip is too thick or the butt needs it more.

But stay in that trough!!!

Don't finish the first side all the way. Go to the second side and start there. You bring the shoulders even and the cut to the middle from first one side and then the other.

You may think you will never get it. No way!!

Stay with it, Buddy Boy!!

You'll find it.

yours Scott

Re: Grinding a Small Chisel

#11

Re: Well then..

ThomD

>I don't mind the small bevels and prefer a much lower angle to the sides. The chisel has the slop of the kerf anyway. I am not convinced it is faster or better to use a tightly fitted chisel either, or that it is therefore required to have a lot of sizes. Didn't stop me from buying different ones.

Re: Grinding a Small Chisel

#12

Re: Some good vids on grinding...

ThomD

>It should be possible to free hand it. That is how I do all my grinding of long bevels. Consider the average knife. Grinding is just turning in reverse

Grinding tips:

Always use a sharp stone or belt, use the coarsest grit possible

Learn to "float" the tool, so that you have a pressure where the tool rides on the belt/stone without it being cut hardly at all. This is the starting position and the means by which alignment is determined, etc...

Lock/hold elbows to side and do as much cutting as possible with body movements

http://www.youtube.com/watch?v=RECV1Sqae3s&feature=PlayList&p=312A9B8E34E6DE24&playnext=1&playnext_from=PL&index=10

You know it isn't really traditional knife grinding if they don't die of lung disease within a year... Great stuff though

http://www.youtube.com/watch?v=SlO-fo_xLRU

http://www.youtube.com/user/watcherknives#p/u

Oh, just noticed the grinders consumption note!

Re: Grinding a Small Chisel

#13

Re: Well then..

Pam Niedermayer, Austin, TX

>No, me either, but I only have a couple or three of these for tight fitting situations but not so tight as dovetails. I like them for chopping wider dovetails, but don't expect the dovetails to come perfectly clean as a result.

Pam

Re: Grinding a Small Chisel

#14

Keep it cool....

Marv

>Scott,

Very good instructions.

In addition to keeping it moving, keeping it cool should be emphasized. Have that container of water close by. The good thing about doing it by hand compared to using a jig is, you can feel the temperature. Always keep the tool cool enough so you can easily hold it. Most of us can stand about 120 degrees F. before it feels too hot to hold. Never be in a hurry. When you are grinding something fairly long like your dt chisel, as you move back and forth, it is best to get into a rhythm and move your whole body, not just your lower wrist and arms.

Imagine hand grinding a hollow ground knife from a file. Once you grind the thin edge and blue it, it has lost it's temper. When that happens to me, I try to not lose mine. *grin*

Marv

Re: Grinding a Small Chisel

#15

A triangular file makes an excellent DT chisel

Marv

>

Re: Grinding a Small Chisel

#16

MARV!!!

Bob Hackett

>We swore an oath to keep that secret!Remember the handshake?

I guess we can safely give them one.

As long as they don`t catch on to the fact that files in general can be turned into all kinds of useful cutting tools I think we`re still safe and our kingdom won`t collapse as long as they keep throwing that "worn out" gold away.

What,what did you say?It`s still on?All this is on record?

So much for the kingdom.:^(

Guess we can drop that awful(and sometimes painful)handshake.

Mainely,Bob

Re: Grinding a Small Chisel

#17

Sorry Bob...I forgot about that handshake. *smirk*

Marv

>Not only can a triangular file be made into a chisel, you can break off the tang end and drill out a file handle and use it as the chisel handle.

Jeeez, Bob, what would they do without all our great ideas? *grin*

Plane irons anyone?

We are too far down this the page in this thread, no one will be reading these posts anyway. The secret will still be safe.

Marv