Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

A55 Smoothing Plane

How do I take a Yankee Screwdriver 130A apart?

Posts

How do I take a Yankee Screwdriver 130A apart?

#1

How do I take a Yankee Screwdriver 130A apart?

Dale Sherman, Manlius, NY

>A friend's father has a 130A which an acquaintance used for a prybar. The spindle shaft is now bent. The only way I know to get it straight is to take it apart, but I can't get it completely apart. What's the trick? Is the shell press fit onto the handle shaft? I took the stop key and set screw out, but it's still on there. Or is there a keeper on the end of the spindle?

I see Stanley carries parts, but not for the 130A. Is there a substitute for the 130A spindle?

Dale, befuddled by yesteryear's engineers

Re: How do I take a Yankee Screwdriver 130A apart?

#2

Re: How do I take a Yankee Screwdriver 130A apart?

Marv

>I've never taken one apart, but I think I'd start by knocking out those two steel pins that are at the front end of the plastic handle.

The parts are probably interchangable with the No.30 with the wooden handle.

Marv

Re: How do I take a Yankee Screwdriver 130A apart?

#3

One small suggestion

Bob Hackett

>You may want to follow the lead of the auto body industry and attempt to take as much of the damage out as you can before disassembling.

If more than one part has been bent you stand a better chance of bending them back proportionately if they remain together.

MB

Re: How do I take a Yankee Screwdriver 130A apart?

#4

Tried that

Dale Sherman, Manlius, NY

>Had some success, but the worst of the bend in the spindle is inside the shaft. It appears that there is some sort of a clip on the end of the spindle inside the wooden handle. Not sure how to get to it to take it off. I know that once the spindle is out, it'll be easy to straighten, or replace.

Dale

Re: How do I take a Yankee Screwdriver 130A apart?

#5

Re: Tried that

Richard Darjes

>I did what you want to do with a Yankee 135. The metal barrel is continuous inside the handle and there are a couple of small barbs bent out on the barrel to hold the hollow wooden handle onto the tool. The screw at the end of the handle actually screws into the barrel so you must remove it first. It took some force to pull the handle off the tool. I can't remember how I did it but it left two small groves on the inside of the wooden handle. When I put the handle back on I first rotated the handle a little so that the barbs didn't line up with the grooves.

Once you have the handle off there are cut outs in the barrel that allow you to pull the retaining clip off the end of the spiral shaft. The clip is made of fairly soft metal (on mine) and I needed to squeeze it with pliers when I put it back so it would stay in place.

All in all, it was way more work than the tool was worth. Are you sure you don't just want to get another one?

Rick in Oakville (Canada)

Re: How do I take a Yankee Screwdriver 130A apart?

#6

130A and the 30a

Todd Hughes

>The 130A and the 30A screwdrivers are the same screwdriver except the 130 has a screw in the handle so it has the quick return feature. These are the ones that the bit jumps out when you release the collar...The yankees that have this feature will have the "1' prefix in the number such as the 135 , 133 etc....

These things are so common and cheap even in the old tool hell I live in I sure don't understand putting much time or effert to fixing one like this. I would spend about 5 min. trying to straighten the shaft with out taking anything apart. No luck with that I would open the window up and toss it into the woods and go buy another one for less then $5......Todd

Re: How do I take a Yankee Screwdriver 130A apart?

#7

Re: 130A and the 30a

Marv

>Tood,

I don't have a woods, but I live on the side of a hill. Lots of junk down there at the bottom of that hill.

One time I threw an air operated stapler down there and later had to go down and find it. For some reason, it fixed itself on the way down there because it worked just fine after I retrieved it.

So maybe a 130A screwdriver can fix itself if thrown far enough. In your case bouncing off a tree in the woods could increase it's chances of being straightened.

Marv