Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

100+ Wood Species + Full-Shop Services: Lumber, Veneer, Tools & CNC. Everything in One Place.

Krenov wall cabinet question

Posts

Krenov wall cabinet question

#1

Krenov wall cabinet question

Wiley Horne--So. Calif.

>Hi Folks,

I'm in the final throes of putting together a small, single-door wall cabinet. It's a little over 21" high by 17" wide by shallow depth. V-shaped door, projecting outward, with glass.

I've been at this point before, and am never happy with how to do this. The problem is very simple--installing the little bars that back the glass and hold it in place. As I understand it, the typical way to install is with brads through the little bars and down into the stiles and rails. If you go that way, surely you have to predrill for the brads--otherwise you're hammering thin wire brads into hardwood and trying not to break the glass in the bargain.

But how to do the predrilling....I will have to use a small drill--a number drill, less than 1/16"--the little brads mic at 0.048" or so. Which means I need an electric drill with a big chuck on it, which is capable of closing on that tiny brad. To locate the bars for predrilling, I need to use the glass, or a spacer the same thickness as the glass. The big chuck means that I can't use the actual glass to set the location for the bars, unless I drill at about 45 degrees, so I guess I need to find or make very low spacers--little strips about 1/8" thick, the nominal thickness of the glass, to press things into place and do the drilling.

But the ripply, lightly-seeded glass is a bit irregular--it's not exactly 1/8" thick down its length. So the spacers will be an approximation.

Plus I'm not totally happy with brad heads showing, even if they're correct for the purpose.

The whole business would be a lot cleaner and simpler if there were some sort of adhesive product that could be used to hold the bars in place behind the glass, where the adhesive holds reliably, but is not permanent....meaning you can get the bars back out to replace the glass if there is an accident in the future. I'd really like to proceed very simply: Get the glass into place; then put a bead of adhesive behind the glass; then press the retaining bars into the adhesive; and be done.

Is there any such adhesive? Or alternatively, maybe I'm just dumb and am doing the brad installation in a difficult way.

All help/advice/scoldings/war stories--will be much appreciated.

Wiley

Re: Krenov wall cabinet question

#2

Re: Krenov wall cabinet question *LINK*

Paul M.

>Hi Wiley,

I've never gone the brad approach myself. I've always made a thin half-lapped frame that has some integrity on it's own and used small screws with decorative washers into the door to hold this frame and the glass under it in the panels. The link below shows what I used. If you have only a few loose wood pieces (i.e. they are not made into a framed insert), then this won't help as the wood pieces can slide out. The screws do not go through the insert at all, but just into the door and the washer overlays the insert. This method will stay put forever, and is easily fixed if the glass breaks.

I have a lawyers bookcase at home that was made with the glass just stuck into the rabbet of the lifting door with silcon sealant. No wood backing at all. One of the glass pieces came loose after many years. My poor wife lacerated herself pretty bad reaching into the case with the glass dangling down precariously. This case has no value, so I just snotted the glass back into place. So beware that this does give way after a while. I would choose a mechanical means to attach the glass retainer rather than an adhesive. Either brads or screws would be better than snot.


decorative washers

Re: Krenov wall cabinet question

#3

Re: Krenov wall cabinet question *LINK*

Bill Houghton, Sebastopol, CA

>I predrilled the wood strips holding our art glass in place on the kitchen cabinets, using a spacer that approximated the right (maximum) dimension, and then applied thin, narrow strips of foam weatherstripping to the back side of the door's rabbet or the strips of wood (can't remember, and can't see the weatherstripping now) to compensate for the differences. It's worked fine, and the glass doesn't rattle.

Would a bolection molding work in the design? You could then face nail or screw to the back side of the door.

Myself, I incline toward screws for molding used to hold glass in place - easier to remove later with less damage when the glass gets broken.

I've seen, but never used, moldings - plastic, I think, which hardly seems Krenovian - with a lip that are designed to slip into a slot cut in the side wall of the rabbet (side wall if you consider that the glass is sitting on the "floor" of the rabbet). See linky below to Rockler's version of this molding.


"Plastic panel retainer"

Re: Krenov wall cabinet question

#4

Jack Guzman from Maine

Brads

Jack Guzman from Maine

>Wiley,

I build clock cases and restore/repair old clocks. Most old clock glass is held in with thin wood strips and brads.I bought a pin vise for this job. If you're not familiar with it,it's a tiny drill that you operate with your fingers.It uses miniature drill bits. Usually with old clocks regular brads were used with coarse strips of wood ,so that's what I do.However when I build new,I use hardwood strips to match the door wood and use brass pins instead of brads.I drill,push them in then finish with a tiny nail set I have just for this job. Pin vises are available from most woodworking tool suppliers.To avoid rattling I use a tiny dab of silicone in a few spots.----Jack

Re: Krenov wall cabinet question

#5

Re: Krenov wall cabinet question

Chris Friesen

>What about wooden backing strips held with hide glue or plain white glue? Both are reversible with water.

Re: Krenov wall cabinet question

#6

Re: Krenov wall cabinet question

R.J.Whelan - Sierras, California

>Wiley ...

Here's how I do it:

1. Cut, mitre, fit and finish the stops

2. Remove the stops

3. Predrill the holes for the nails

4. Counter sink the hole using a micro router bit I bought specifically for this task chucked into an egg-beater drill (I remember seeing this in one of JK's books which is where I got the idea.

5. Install the glass and stops

6. Cut the heads off of a bunch of tiny finish nails

7. Push the headless finish nail into the hole using a pair of needle nose pliers

8. Place a piece of card stock against the glass - this protects the glass during the next step

9. Drive the nail with a small square headed hammer (I use a little 2oz Japanese plane adjusting hammer). Slide the hammer back and forth on the cardboard and take light taps. Be sure to back up the edge of the side being hammered to eliminate rebound.

10. Counter sink the headless nail slightly

11. Fill the hole with an appropriately coloured wax pencil - I think the ones I have are made by Minwax

As the stops are mitred they are really locked into position and the nails just keep them from being lifted out.

I do remember seeing that JK uses a little scrap of wood that's the exact thickness of the glass and he places a couple of these dummies under the molding and predrills the stops and frames before installing the glass.

Good luck ........ rj

Re: Krenov wall cabinet question

#7

Part II

R.J.Whelan - Sierras, California

>Wiley ... I checked on the filler. It is by Minwax and is called "Blend-Fil". It's in the form of a pencil, comes in several colours and looks like a grease pencil, if you remember what they are ........ rj

Re: Krenov wall cabinet question

#8

Re: Krenov wall cabinet question

Bill Tindall, E.TN

>I need to see a picture of then need, but if it is like the case I made the vertical divider strips are not nailed. The vertical wood divider strips float between the panes and extend into the door rails. These vertical wood divider strips are held in place with another wood strip notched to accommodate the vertical strips and nailed to the door rails (horizontal parts of the door frame). Let us call this the "holder strip".

I installed the glass with its vertical divider strips. I pre-drilled the holder strips with holes the enabled the brads to be press fit into the holes. Placed holder strip in place and tapped the brads to make a mark. Removed everything and drilled where the marks were made.

It takes little force to hold the holder strip in place so the pilot holes are about the same size as the brad diameter, in fact I probably used the same sized drill. Then I assembled everything and pushed the brands in place and set them gently.

Get over fretting about using brads.


img

Re: Krenov wall cabinet question

#9

Bingo

Wiley Horne--So. Calif.

>Bill,

I never thought about using the two step procedure for pilot drilling. That will do it. I may combine that with RJ's invisible brad method, or else just get over it, as you suggest.

Thanks! That's a solution.

Beautiful detailing on your case!!

Wiley

Re: Krenov wall cabinet question

#10

Re: Krenov wall cabinet question

Warren in Lancaster, PA

>Wiley, I use a Millers Falls drill for this kind of work. I did not know that some chucks could not hold small bits

Re: Krenov wall cabinet question

#11

Confession

Wiley Horne--So. Calif.

>I don't own a single egg beater. Holy Cow!! How is that possible? I was referring to real small braces as well as the push drills in my comments.

This is a good chance to go find a Millers Falls eggbeater. Which is the one to get? #2 or #5?

Wiley

Re: Krenov wall cabinet question

#12

Ask and ye shall learn!

Wiley Horne--So. Calif.

>jack,

Just went and looked up 'pin vise'. That is a great solution. I think I will use Bill T's two stage approach for right now, since I can go ahead and not wait for the mail to bring a new tool.

But the pin vise approach will be perfect for this job in the future. And it's the same issue on every glassed door.

Thanks a lot!

Wiley

Re: Krenov wall cabinet question

#13

Re: Part II--Found it! *LINK*

Wiley Horne--So. Calif.

>RJ,

Great suggestion. I found a link to it, which is posted below for benefit of others.

Now if I can just do a neat job tapping that headless brad down......

Wiley


Minwax Blend-fil pencils

Re: Krenov wall cabinet question

#14

Re: Krenov wall cabinet question

Wiley Horne--So. Calif.

>Paul,

Ouch, that's a bad story about your wife hurting herself like that. And it really does show you have to have a mechanical solution, and reversible adhesive would be risky--thank you very much. I think I will go with brads, but your solution is sure-fire.

Thanks,

Wiley

Re: Krenov wall cabinet question

#15

Re: Krenov wall cabinet question

Wiley Horne--So. Calif.

>Bill

Lots of good ideas. I like the bolection moulding one especially. In this case, it would work physically, but sorta goes against the Krenov minimalist look, so I think I will go with the strip-type stops. On a different project, especially a larger project, the bolection moulding would be great.

Wiley

Re: Krenov wall cabinet question

#16

scott grandstaff

eggbeaters

scott grandstaff

>You can't go far wrong with either Millers Falls. Both are wonderful.

But don't forget Yankee! A small 1530 with the 5 speed transmission?

And for small eggbeaters, nobody beat Goodell-Pratt.

Here is the little G-P I did recently. These are exceptionally small with a chuck that only takes a 3/16 bit max.

The caps are always missing. I made this padouk cap.

The trick with these is tapping into sidegrain. End grain rips out too bad. But sidegrain you can tap with a sharp tap really easy.

yours Scott


img

Re: Krenov wall cabinet question

#17

Framing "pliers?" *LINK*

Bill Houghton, Sebastopol, CA

>I haven't tried these, but a lot of the vendors sell devices for driving brads in this exact application - link below is to Lee Valley's version. They're marketed for picture framing, but, if the stiles on your doors are narrow enough, I see no reason why they shouldn't work on a cabinet door, although the hardness of the wood might defeat the tool.

What I have used for this kind of brad driving is regular old "channelock"* pliers, with a little painter's tape on each jaw (one layer on the "driving" jaw, several on the clamping jaw). These work marvelously enough that, until I undergo a sudden career change and become a FT picture framer, an unlikely event, I don't need the brad setters.

It's REALLY hard to break glass with this approach. You'd have to drop the pliers.

I can definitely sympathize with concerns about the glass, though. The art glass for two kitchen cabinet doors cost $200. When I brought the glass down from the shop to the kitchen, where I was installing it in the doors atop layers and layers of newspaper, I walked like a man carrying his firstborn across a tight rope in a room filled with vampire bats.

*Yet another example of a maker who does such a good job of developing a particular tool/device/thing that the maker name becomes the generic name. Think "kleenex."


Others sell them too

Re: Krenov wall cabinet question

#18

Neither

Bill Houghton, Sebastopol, CA

>North Bros. eggbeaters are the way to go. The 1530, as Scott suggests, is great for small bits. I recently picked up a 1545 (I think it is, too lazy to go out to shop) that is, in my opinion, superior to the M-F No. 2 for mid-size bits.

The M-F No. 2 is really kinda big for the sorts of holes you're discussing.

Re: Krenov wall cabinet question

#19

scott grandstaff

glass hammo

scott grandstaff

>You can always make a little window hammer to drive brads (or to drive points in your regular casement window repair).

Lay the head down and slide it along the glass, driving your brad or point. Works every time.

I made this one up from scrap. Pretty simple for a tool job. Block of scrap steel and length of 5/16 rod.

I have used it whenever the occasion arose for 25 years or so now, so the design is trustworthy.

Also shown is a window chisel for removing old glazing and adjusting window rabbits, and a small flat plate I filed out to hold triangular points for driving without damagin my fingers.

My wife Kitty painted the little points box for me one day when she was in a good mood. :)

For your tiny molding work Wiley, I like brass straight pins. These are available at quality sewing paces. The shaft is very tiny and the wide head is pretty attractive if you arrange them along the molding well.

yours Scott


img

Re: Krenov wall cabinet question

#20

I like the box!

Scott Burr in Ben Lomond CA

>That hammer on the other hand looks awful ruff...8^)

I like your glazing chisel. I usually use a Stanley #45 chisel that 2" wide. After all if your removing glazing, the glass is all ready gone...

Re: Krenov wall cabinet question

#21

Gotta agree on the G-P's

Scott Burr in Ben Lomond CA

>I have 2 and their wonderful. My smallest can hold a bit so small I won't attempt using them in it for fear of breaking the bit DAMHIKT. Usually happens after a few cups of coffee.

Re: Krenov wall cabinet question

#22

scott grandstaff

Re: I like the box!

scott grandstaff

>Hey, did I mention I made that hammer 25 years ago,.. and in an hour??

hee heheheh

Yup, its pretty crude, but effective. Custom tools were a long ways away. I am not sure how many people were even making custom tools anywhere then. I am sure there were a few. Paul probably. But then even the great Hamler starved for some time in the early days.

The box is much cuter in person.

Even that picture was taken when it was meant to be shown on a 28.8 baud modem.

The glass chisel is practically a miracle when working on old windows. Saves you skin like you can't believe. Cs Osborne made a great one but several others made them too. Glaziers chisel they sometimes call them. The blade flares out a bit and with the heavy crank neck, gets you into corners nice.

yours Scott

Re: Krenov wall cabinet question

#23

nice to have but won't solve the problem

Bill Tindall, E.TN

>I have two pin vices and neither would have a small enough chuck to drill the holes with the glass in place. The pin chuck that one can operate by hand has a chuck as large as an egg beater drill, the tool of choice for these delicate jobs. The other holds tiny number drills and it is chucked in a larger drill chuck. One could, I suppose, turn it by hand but it would be a tedious way to make a hole.

Re: Krenov wall cabinet question

#24

hard to get one up on Warren

Bill Tindall, E.TN

>I have a numbered drill set that goes down to a number 80 (0.013"). The Milers Falls is ideal for chucking the pin vice that holds these tiny drills.

Re: Krenov wall cabinet question

#25

Wiley!! Egg beaters are Wonderful!

Bill Tindall, E.TN

>How can you build with out a small egg beater drill? I have several. I like the kind with two small gears as I think they run better. When I am installing house trim I have three equipped with a drill for each size finish nail to be used. An egg beater is to a power drill as a chisel is to a power planer. They provide so much control for delicate hole making.

I find the larger ones useless. In my hands they are only useful for small drills. Somewhere around 3/16" it's time for the cordless.