Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Portable Sawmill & Tree Service – Abingdon, VA

Cherry for Chisel handles?

Posts

Cherry for Chisel handles?

#1

Cherry for Chisel handles?

Al

>Howdy folks. I have a bunch of old tanged chisels that I need to re-handle, cherubini style, and I happen to have had a large cherry tree fall over in the meadow.

I was thing of cutting some logs out of the trunk and then splitting stock out of them to use as the chisel handles. After letting it dry for a while.

I generally will use these chisels with hand pressure only, but there will be times that I tap them along with a mallet.

I am mostly concerned about how the cherry will hold up around the tang. I don't want to be pushing a chisel along with my shoulder and have it split out of the handle.

Will cherry be too brittle? I'm not planning on ferrules at either end of the chisels, so the wood will have to survive on its own.

Thanks for any input.

HB

Re: Cherry for Chisel handles?

#2

Re: Cherry for Chisel handles?

Stephen Shepherd in the State of Deseret

>I would think cherry is to brittle for chisel handles. When cherry splits it splits fast and you could risk a tang in the palm with catastrophic failure.

I use curly maple for all of my chisel handles, octagonal in profile to prevent rolling and tapered with a bigger end for my hand. I have pounded on them and none have ferrules and haven't broken one yet.

Stephen

Re: Cherry for Chisel handles?

#3

Re: Cherry for Chisel handles?

Marv

>Al,

Why not use ferrules? You'd only need them on the chisel end. Just find some tubing at your local hardware store that will be a convenient size and turn the handles to press fit. Just cut the tubing with a hacksaw and file the ends smooth. Or if you have a belt sander, even easier. Do a full radius on the back end of the handle so when you do need to tap it, you will be tapping the center area where it will be less apt to split. Or get a bigger size tubing for that end.

Marv

Re: Cherry for Chisel handles?

#4

Re: Cherry for Chisel handles?

Paul Dzioba

>I think the cherry will be fine. Just make sure the bolster is seated well against the handle. I like to pre-drill a pilot hole and 'burn' the handle on. Place the chisel tang facing up in a metal vise, heat to red with a torch, and then push on the handle. Immediately remove the handle and cool the tang with a wet rag. Perfect fit every time, just mark the handle so you put it back on the same way. It will smoke up your shop some but the cherry will smell nice. Just be careful and don't burn yourself or your shop.

Paul Dzioba

Re: Cherry for Chisel handles?

#5

Re: Cherry for Chisel handles?

Bob Hackett

>The cherry I used for my socket chisel handles has held up well for 6+ years under the same conditions you talked about.

I would recommend you take Marv`s advice about using tubing at the tang end.Cheap and easy insurance against splitting.

MB

Re: Cherry for Chisel handles?

#6

Re: Cherry for Chisel handles?

ThomD

>You could use balsa in that application. I have canoe paddles with red cedar shafts. With Cherry I have mounted file handles on cherry ornamental cuttings by just driving them into the pith. You can just cut round branches and use those the way the Japanese do, you need to find a non-rotten pith, but it gives perfect grain orientation, and you get that pretty look where you have straight grain visible from 360 degrees.

As another example.you can shoot a cedar arrow shaft, 11/32", in a socket head through a bull moose at 200 fps. You should be fine.

Re: Cherry for Chisel handles?

#7

Re: Cherry for Chisel handles?

John L Blue

>That ol' Cherry Tree, I just finished up a coupla walkin' sticks from some Wild Cherry, think about that. Let'em sit a buncha months, let'em split, fill'em with sawdust,glue,woodfiller,etc.