Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Rare Exotic & Domestic Hardwoods, Milled In-House in Oregon. Browse Unique Stock.

Hinge question

Posts

Hinge question

#1

Hinge question

Edward in Vancouver

>I am building a "twin" chest for my Veritas-plan toolchest that I made last year. Its my intention to have the Veritas chest sit on top of the new one. It would have two doors, no central stile, with one half full of drawers, and the other half ample room to "Park" my small collection of planes.

I have family members "borrowing" tools occasionaly, and for this purpose I have all my garage-sale finds (chisels, tool-box saws, etc) on display on the peg-board, and the "good stuff" in the locked chest. (Did you know that Jap. saws loose their teeth easiy when used as pruning saws? I found out the hard way...)

I want to design the new chest with two inset doors, that is the doors fit in within the carcass, and so that ony the face of the door is visible--no access to any edges. The left side would be held in place with a bottom dead-bolt and an upper magnetic push in- push out catch, (push the door 1/8" in and it pops out 1/2") and a mortised lock in the right door with the same upper magnetic catch. With no knobs or protusions the doors can not handled or opened unless you either A)have the key, or B) in the case of it being unlocked, know the "secret" that you have to push the doors in before they pop out.

The carcass material is 1/2" qswo, but what type of hinges do I use?

I would like the doors to swing back, along the sides. I don't think a regular butt-hinge would let me do this.

Would a double-offset knife hinge work?

Regards,

Edward

Re: Hinge question

#2

Knife hinge

Wiley Horne--So. Calif.

>Hi Edward,

Tough problem, because it is a full inset door. With an offset knife hinge, think about the projection of the hinge from the front surface of the door. The only thing that gets your door 270 degrees around the corner, is if the projection of the hinge--the distance from the front surface of the door to the center of the hinge pivot--is equal to the thickness of the case side. So in your case, you would need an offset knife hinge with a 1/2" projection, and at that, you would have to mount the hinge visible at the front edge of the door (rather than mortised into the interior of the door edge).

What's more important, the 270 degree swing or the full inset? If you were to rabbet the inside front edge of the carcass by 1/4", say, and set the doors into those rabbets so that the doors partially lapped the case sides, then an offset knife hinge could be found to get you around the corner. You would only need a hinge projection of 1/4". But getting around 1/2" of case side a full 270 degrees is tough.

Wiley

Re: Hinge question

#3

Re: Hinge question

James Watriss

>I think you should Google images of Krenov cabinets. I'm pretty sure you'll find what you're after.

Good luck with this... my downstairs neighbor found out how fast my Japanese saw will lose its teeth when you try to cut a box spring in half. I was not impressed.

Lucky for me it was a Home Despot Marples brand saw, and not one of my good saws.

Re: Hinge question

#4

Re: Hinge question

Bruce, a MN Galoot

>I can't envision the type of hinge it would take to do it if the doors are inset. However, if the edge of the doors sit flush with the side of the cabinet, Blum makes one that allows a 270 swing. I have a set on a tv cabinet that allows the inside to be completely open and the doors against the side. Let me know and I'll ferret out the model number.

Bruce

Re: Hinge question

#5

Re: Hinge question

Edward in Vancouver

>Thanks Bruce, but the door thickness is 1/2".

I don't mind the knuckle of a knife hinge stick out, but what I am worried about is having a regular butt hinge that only allows me to open the door 90 and then if I bang the door, it would put stress on the door and carcass. I could use chains to stop the door, but I dunno...

My options for hardware are the usual Borg schtuff and LV. By far LV has the most options, albeit for thicker doors (5/8" and up)

So far the knife style hinge looks like a viable option right now.

Thank you for your responses

Re: Hinge question

#6

Take a look at these *LINK*

Wiley Horne--So. Calif.

>Edward,

The hinge linked below has the longest projection of any I have found. The long arm of the hinge is 1-3/4"; the shorter arm is 1-1/8". Of that 1-1/8", it appears to me that approx. 3/4" is net projection beyond the longer arm.

If that is so, then you could do a nice installation of these, insetting them, say, 3/16" into the edge of the door, and still have 1/2" to 9/16" projecting beyond the door face. That would get you around the corner. Please do your own scaling and math to check mine.

Note that these particular hinges are 'handed'. You would need both a left-handed and a right-handed pair.

Wiley


Offset knife hinges--long projection

Re: Hinge question

#7

Cut a box spring in half?

Bill Houghton, Sebastopol, CA

>Was s/he trying to make a twin into a double or something?