Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Reach the woodworkers who ACTUALLY BUY

A Primer for Handcut Mortice-and-Tenon Joints *LINK*

Posts

A Primer for Handcut Mortice-and-Tenon Joints *LINK*

#1

A Primer for Handcut Mortice-and-Tenon Joints *LINK*

Derek Cohen (in Perth, Australia)

>Well, the full title is a real mouthful, and it could not fit in the teeny weeny Subject box (we need something longer for fellows with a more verbose style, such as I).

I have just placed a new article on my website: A Primer for Handcut Mortice-and-Tenon Joints. Part 1: The Blind Joint. (link below).


The wardrobe is taking shape, and I thought I'd take a few snaps of these joints along the way.

As always I am open to ideas for changes. Anyway, the forum has been quiet for a while, and this may spark some discussion.

Regards from Perth

Derek


A Primer for Handcut Mortice-and-Tenon Joints

Re: A Primer for Handcut Mortice-and-Tenon Joints *LINK*

#2

Re: A Primer for Handcut Mortice-and-Tenon Joints

Marv

>Hi Derek,

Great tutorial, even I can follow it.

Regarding the 1/3 rule, is there a similar rule for the depth of the mortise?

Thanks,

Marv

Re: A Primer for Handcut Mortice-and-Tenon Joints *LINK*

#3

Re: A Primer for Handcut Mortice-and-Tenon Joints

Derek Cohen (in Perth, Australia)

>Hi Marv

Both the width and the depth of the tenon - and therefore the mortice - generally follow the 1/3 rule. It is a guideline only.

Regards from Perth

Derek

Re: A Primer for Handcut Mortice-and-Tenon Joints *LINK*

#4

Jesper, Denmark

Re: Derek, Your tutorials are always a Joy.

Jesper, Denmark

>

Re: A Primer for Handcut Mortice-and-Tenon Joints *LINK*

#5

Alternative to "perfect" shoulders, maybe faster

Bill Tindall, E.TN

>I enjoyed you presentation. One begins to wonder if such quality efforts are going to replace books.

I saw nearly to the scribe line that defines the length of the tenon and then pare back to the scribe line with a chisel (similar to the technique used for chopping out dovetail waste to its base line ). This way is fast and ensures a uniform tight fit of shoulders to stile. If sawed close to the scribe line one whack with the chisel is sufficient to remove the waste.

I learned this technique in a class in the Mack Headley & Sons shop. We did the sawing free hand with a band saw which leads to the fastest way to make a nicely fitting mortise as I have found.

Re: A Primer for Handcut Mortice-and-Tenon Joints *LINK*

#6

Re: A Primer for Handcut Mortice-and-Tenon Joints

Victor Parisian

>Thanks for posting. Great work as usual.

Victor

Re: A Primer for Handcut Mortice-and-Tenon Joints *LINK*

#7

comments on the 1/3 rule

Chris Friesen

>I've often thought that this rule is misunderstood. The worry is primarily about blowing out the sidewalls of the mortised piece while making the joint, or else making them so thin as to weaken them.

If the stock being morticed is thicker than the tenoned piece (a leg/apron joint for instance), then the thickness of the tenon can be much thicker than 1/3 the thickness of the apron stock without any danger of weakening the mortise walls.

With hand tools, on thin stock a mortise of much more than 1/3 the thickness of the stock starts to get dangerous. With power equipment, 1/2 the thickness of the stock being mortised is easily doable.

As to the length, I thought the general rule was 5x the thickness of the tenon, since you don't gain much strength by going longer. On the other hand, the Shakers often used very long through-tenons, even on thin stock. I suppose this could be useful if you were wedging them rather than drawboring.

Re: A Primer for Handcut Mortice-and-Tenon Joints *LINK*

#8

Thanks Derek, I've read all of your material.

Tom Colligan

>