Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

VPS-Level Performance. Fully Managed. No Hassle.

Veneering with hide glue

Posts

Veneering with hide glue

#1

Moses Yoder

Veneering with hide glue

Moses Yoder

>I have some pretty nice bird's eye maple veneer and was thinking about using it for some upcoming picture frames. I am thinking I will just make my own veneer hammer and use hide glue to stick the veneer down. Frames will only be about 1-1/2" or so wide perhaps over walnut so I can chamfer the edges to get a colored bevel. I am thinking of applying the glue with a small foam roller. Has anyone veneered with hide glue, and if so I would appreciate any pointers.

Re: Veneering with hide glue

#2

Re: Veneering with hide glue

Hank Knight

>Moses,

I'm no expert by any means, but I've done some hammer veneering. I just painted my glue on with a good sized brush. Use lots to make sure you get good coverage. You know to spread glue on both sides of the veneer. My only comment is that hide glue has a fast tack, so work fast. It's all over when the glue starts to cool. I know you can reheat the glue and reposition the veneer, etc., but it's so much cleaner to get it right the first time. I don't know how people hammer veneer large pieces.

Good luck. Post pics.

Hank

Re: Veneering with hide glue

#3

Re: Veneering with hide glue

Eric Hartunian

>I veneered a small tilt top table with a veneer hammer. I made my own. For the blade, I used that material that disposable cutting boards are made of. It worked great, and is really slick and nothing seems to stick to it. I agree, work fast. What are you using as a substrate? I used pine, and crossbanded it. I would also recommend making a batch of thinned hide glue, and brushing that on as a size first. Let that dry, then give it a light sanding, then apply the full strength glue and the veneer.

Good luck,

Eric

Re: Veneering with hide glue

#4

Re: Veneering with hide glue

ThomD

>I don't think a foam roller would be the ticket, the glue is pretty hot, and can pull back. The typical glue brush is sorta like a bunch of bamboo strands or some such in a bunch, even a brush will get tired pretty quickly.

I made my hammer out of a piece of 3/16" brass stock let into a wooden head, and epoxied in place. I filed the edge round, though a lot of flat stock is pretty nicely rounded to start with.

The hammer sets the glue in two ways. It narrows the bond line down so that very little heat or moisture is left and the glue sets up on contact. The metal sucks some heat out of the glue so that it sets, this is why a metal hammer is prefered, and a metal like brass with good thermal mass and conductivity.

The instructions I read originally said to paint glue on both sides of the veneer, because the glue on top would help the hammer slide around and hold more heat. seemed to work, but I don't know if it is all that useful. Larger pieces really do need some ongoing heating. I use an old iron, and start at some point, usually the middle, but it could be an edge with a book match. I start rubbing it out, but it quickly starts to set. It takes some feel to add the heat where you need it without releasing adjascent pieces that one already had down with minimal glue holding them. But at worst you can start all over again. The first project I tried turned out fine, so I think it is pretty easy and forgiving.

Re: Veneering with hide glue

#5

Re: Veneering with hide glue *LINK*

Marv

>According to Leif Hanson, you should size both sides of the vaneer. If you only size one side, it will tend to curl on you.

Leif Hanson is doing some vaneering and is telling his story as he goes. He's a clever guy and seems to figure it all out and then tells you about the mistakes he makes along the way. I love his tutorials. Click around on his website while you are there, lots of good information and a great useful website.

Marv


Leif Hanson's story

Re: Veneering with hide glue

#6

Paul Kramer

Here's another resource  *LINK*

Paul Kramer

>


St. Roy's show on veneering