Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Support WoodCentral when buying things you need

A finishing question - old cherry...

Posts

A finishing question - old cherry...

#1

A finishing question - old cherry...

John Aniano - in central NJ...

>Hello All,

I need to deepen the color of a number of ~1840 turned cherry spindles to even them out. They have been stripped of their old black matte finish. There are 48 spindles altogether in the staircase and maybe 15 need to a be a bit darker. There is some sapwood present in a few of the spindles. Might potassium permanganate, or some similar chemical do the job? I worry that the wood, being so old, will react unfavorably using chemicals like these. How about using Transtint dyes in alcohol? Or should I look at other options?

I'll ultimately finish the spindles with Tried and True "varnish-oil" - the turned cherry newel post has two coats already and looks great.

TIA,

John

Re: A finishing question - old cherry...

#2

Re: A finishing question - old cherry...

Dan Donaldson

>I think that I would use some type of stain.The chemical treatments would be a lot harder to control for depth, plus would not affect the sapwood the same. The stains would give a lot more control.

Re: A finishing question - old cherry...

#3

Ellis Walentine

Glaze?

Ellis Walentine

>Hi John,

It might be to stain just the lighter ones to match the darker ones, probably involving different dilutions as well as hues and values. You might want to look into using a gel stain to glaze them, and maybe not limit yourself to just the lighter ones. Glaze has the added desirable effect of imparting an antique look to the balusters, by collecting in the recesses of the turnings. I'd experiment on both dark and light balusters and see if it works. You might end up sealing with shellac first to keep the glaze from staining the wood.

Ellis

Re: A finishing question - old cherry...

#4

Darkening Cherry

R.J.Whelan - Sierras, California

>John ...

I have had good results with Trans Tint dyes (Rockler, among others).

I add the dye to 2# cut blonde, dewaxed shellac and apply it with brush, wait about 1 minute and then wipe it with a cotton rag dampened with the same solution. Because the solvent is alcohol you should not have much grain raising.

When I am determining the proper amount and color of dye to use I use a graduated cylinder and usually start with a ratio of about 1:25 (one part dye to 25 parts finish). Sometimes I hit it right on the first try; usually I end up applying the "toner" twice to get the right look.

Good luck ......... rj

Re: A finishing question - old cherry...

#5

Re: Glaze?

Tony - Memphis

>I've had goodluck with that technique. There was a real good article in FWW about it a few years ago. And there was one recently in ??? about making your own glaze with gel poly and artist's oil paint. I playe dwith that some and liked what I saw. Haven't used it on a large project yet. I used the Trans Tint Honey Amber? mixed with a clear gel poly to warm up some walnut. That worked great. My first big project was a cd cabinet with plywood panels. The solid wood and the plywood were very different colors after the clear coat was applied. I used a couple of different colored gel stains to match them up. Very easy to work with. Good luck with it. How about some pics?!?

Tony

Re: A finishing question - old cherry...

#6

Don't do anything.

Bill Tindall, E.TN

>It not like these are boards in a table top. I wouldn't worry about the shade differences in these balusters(?). Nobody is going to notice it.

Re: A finishing question - old cherry...

#7

Re: A finishing question - old cherry...

Stephen Shepherd in the State of Deseret

>Use a glaze of shellac and dry powdered pigments, available from pottery and ceramic supply houses. You can make the shellac any color you want (white is difficult) and use it as a glaze. If you don't like the color you can wipe it off with alcohol.

Don't try and get the color all at once, use a couple of coats. Start out with red then use a burnt umber over-glaze.

Stephen

Re: A finishing question - old cherry...

#8

Start by putting them outside

Kelby

>A few days in the sun will darken cherry a fair amount.

Re: A finishing question - old cherry...

#9

Moses Yoder

Re: Start by putting them outside

Moses Yoder

>Sunlight will make the difference in color between the sap wood and the heartwood stand out more, not less. The sap wood will darken a little bit but not nearly as much as the heartwood.

Re: A finishing question - old cherry...

#10

Re: Darkening Cherry

John Aniano in NJ...

>RJ,

Why did you use the Trans Tint dyes specifically with 2lb blond shellac? Why not just cut it with plain alcohol instead?

John

Re: A finishing question - old cherry...

#11

Re: Start by putting them outside

John Aniano in NJ...

>Kelby,

The spindles were stripped of finish in place. No easy way to get sunlight on them! In fact, they only rarely get direct sunlight and that only in the dead of Winter when the sunlight can get that far into the house. Not an option, sorry.

John

Re: A finishing question - old cherry...

#12

Re: Lye solution

ThomD

>A solution of 1 ounce of lye to a gallon of water will darken cherry. It needs to be neutralized afterwards with water. Lye is very dangerous and probably shouldn't be used. If you wanted to do this in a profesional setting OSHA might well hamper you.

I always let cherry just reach it's own colour which it will do rather quickly. I never tint or dye it, largely because the long term results are just as bad as the short term ones. I guess one could call that a two for one deal.

Re: A finishing question - old cherry...

#13

Re: A finishing question - old cherry...

John Aniano - in NJ....

>Thanks all for the suggestions. I just may leave them as-is, apply the oil finish and see how the color deepens. Later I can touch up any light colored spindles, if they are that offensive.