Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Portable Sawmill & Tree Service – Abingdon, VA

Re-surfacing waterstones

Posts

Re-surfacing waterstones

#1

Re-surfacing waterstones

Sawman

>This past weekend I started to re-surface my waterstone. In 20 years I had never done it! I never thought to put a rule on them> Boy what a dish shape I had. So I started with sandpaper on glass. I went through countless sheets doing the 800 &1200. When I got to my 320 I started with a concrete block then went to the paper. Still slow. I found some 90 grit lapping compound tucked away in the clutter. Put a little bit on the glass plate added water and in short order one side of my 320 stone was done. Gave it a rinse and checked it with the rule. Perfect!

Now for the remaining side and I will never let them get like this again!!

Re: Re-surfacing waterstones

#2

Re: Re-surfacing waterstones

brian greene

>Try 100x drywall screen. That's the metallic abrasive used for sanding drywall compound. I put it on 1/4" plate glass backed up with 3/4 melamine or plywood to eliminate any possibility of the glass flexing.

Pencil some indicator marks on the wet stone. I typically do my 250 and 1000 stones in this manner. I do the 4000 on the 1000 and the 8000 on the 4000.

Also, I typically lap my stones every time I use them. You cannot achieve truly sharp,consistently, on stones that are less than flat. It usually only takes a couple of strokes.

This method is fast, inexpensive and comparatively clean.

Cheers,

Re: Re-surfacing waterstones

#3

Re: Re-surfacing waterstones

Sawman

>Great idea! Thanks

Re: Re-surfacing waterstones

#4

Re: Re-surfacing waterstones

Ron Bauman

>I do my oil stones every 5-10 years (I don't think this is a gloat at least I'm not very proud) using #60 abrasive I bought a coffee can full of about 25 years ago. Sure is nice for a few years.

Re: Re-surfacing waterstones

#5

possible problem

Bill Tindall, E.TN

>You may have relatively coarse grits from the lapping compound embedded in the soft matrix of the water stone. So, you may need to do some abrading with the water stone on some scrap before using it for fine work.

What kind of paper did you use? Wet-dry Silicon carbide would be an exceptionally poor choice. The brittle silicon carbide particles will shatter to doodle dust when abrading the tough aluminum oxide in the water stone. An old coarse sanding belt, ideally with zirconia abrasive, would be best in the sand paper category. Stick it down to something flat with contact cement.

Re: Re-surfacing waterstones

#6

Re: possible problem

Sawman

>I only used the lapping compound on my 320 grit stone.

The others I used wet/dry paper.

Re: Re-surfacing waterstones

#7

This is what I do....

Marv

>While wandering around in Harbor Freight one day I saw a neat look'n abrasive block. It was four sided about 6 inches long. Each side had perforated screen that is coated with diamond dust. 200 through 600 grit. The sides are nice and flat. It even has a neat little base that it snaps into to keep it from sliding around.

Works super fast on any stone for rough flattening and or just renewing a glazed surface. Doesn't really matter what grit your stone is, all you really want is to make it flat again. The stone will remain the same grit.

Marv

Re: Re-surfacing waterstones

#9

Re: possible problem

Brian Greene

>The drywall screen presents no contamination issues ... it's dead simple.

Re: Re-surfacing waterstones

#10

Re: And from now on... The real answer

ThomD

>Simplest system I have found for maintenance if you use artificial stones is to get two of the same stones in your coarse, say 800, grit. These are usually pretty cheap. I ahev the same brand though it might not mater, but probably does. After they are surfaced, or when new, just rub them together to keep them flat, and then use one of the 800s for your next stone and on up. Keeps the stones in good shape with minimal paraphenalia. There is a lot of huey about this contaminating stones, but if it is good enough for Scot Neihring, it is good enough for most of us.

Also sharpen on the parts of the stone you don't currently sharpen on. You need to rub on the donut, not just the hole. Not all tools are suited to all parts of all grit stones, but with comon sense you will reduce dishing, and the need to be rubbing your stones together to keep them flat. Sharpen very narrow tools,etc... on the sides, or use harer stones like oil stones for them or ceramic.