Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Personalized Wooden Watches, Engraved Free

A bowsaw in the wild! A rarity in this area!

Posts

A bowsaw in the wild! A rarity in this area!

#1

A bowsaw in the wild! A rarity in this area!

Bill Houghton, Sebastopol, CA

>this is the first one I've seen (and, thus, the first one I bought...).

Looks commercially made, although the toggle made from a scrap of framing lumber and the tensioning line made from shipping twine are probably not OEM. It needs a little work (other pics in attached messages), but for $5 seemed worth it.

It's had some action from what looks like anobiid beetles, visible toward the right end of the cross piece but scattered around (I'm thinking of them as lightening holes) - does anyone know if these can be frozen dead? If so, I'll bag it and put it in the freezer for a few days.


img

Re: A bowsaw in the wild! A rarity in this area!

#2

The hole for one handle was drilled crooked

Bill Houghton, Sebastopol, CA

>but I suspect I can live with that.


img

Re: A bowsaw in the wild! A rarity in this area!

#3

And one tenon is maybe a bit long

Bill Houghton, Sebastopol, CA

>but that will be easy enough to correct.


img

Re: A bowsaw in the wild! A rarity in this area!

#4

Should have done my internet research

Bill Houghton, Sebastopol, CA

>According to several sources, freezing temps will kill these beetles - one week at freezer temps.

It also appears they could be anobiid or lyctid - same cure for both.

Now to convince LOML that a plastic-wrapped bowsaw will be a good feature for the freezer drawer...

Re: A bowsaw in the wild! A rarity in this area!

#5

Tenon too long?

Stuart Hough

>Might have been designed that way so there will be a pivot point for the tightening process. If you trim it so that it seats fully, you'll be putting pressure on the sharp-edged shoulder, which seems a good way to start a crack at that site. JMHO

Re: A bowsaw in the wild! A rarity in this area!

#6

Could be

Bill Houghton, Sebastopol, CA

>but the other tenon seats down to the shoulder, which I think was the intention.

Re: A bowsaw in the wild! A rarity in this area!

#7

Questions on refurbishing this bowsaw

Bill Houghton, Sebastopol, CA

>I started taking it apart tonight. The handle pins are 3/32", which I know because my 3/32" pin punch is getting trapped in the hole (need to dig down a bit in the hammer-and-punch drawer for the 1/16" punch). The previous owner, apparently having lost one pin, drove in what looks like a nail and peened it over on one end. Am I correct in thinking that a 3/32" drill bit would be good stock for a new pin?

What are the choices for the tensioning line, and where might one find them? The packing twine currently on it looks a bit frail.

Re: A bowsaw in the wild! A rarity in this area!

#8

For tensioning line, I've used Lee Valley's

Chuck Nickerson

>utility cord for the several bowsaws I've built (from the TFWW kits). The LV utility cord come in three strengths. I use the medium test (96#). The lightest test breaks, and the heaviest test looks too coarse to my eye on a 12" bowsaw.

Re: A bowsaw in the wild! A rarity in this area!

#9

Thanks for the suggestion

Bill Houghton, Sebastopol, CA

>My local hardware store carries similar braided line in multiple diameters. Have you found your line stretches and needs adjustment?

Re: A bowsaw in the wild! A rarity in this area!

#10

Re: Questions on refurbishing this bowsaw

Stephen Shepherd in the State of Deseret

>Use 1/4" diameter manila or hemp rope and end splice it together to form a continuous loop. Takes a little practice to get the length right, but the end results looks much better than a string with a knot.

Stephen

Re: A bowsaw in the wild! A rarity in this area!

#11

Re: Thanks for the suggestion

Chuck Nickerson

>I've probably tensioned it fewer than 50 times. In that time it might take one more turn to get it right; nothing significant.

Re: A bowsaw in the wild! A rarity in this area!

#12

Jack Guzman from Maine

Re: Could be

Jack Guzman from Maine

>I repaired a bowsaw in the colection of a local museum.It had a similar problem.I found the crossbar had been installed backwards.When I flipped it end for end,the tenons fit perfectly.Just a thought.---Jack