Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Rare Exotic & Domestic Hardwoods, Milled In-House in Oregon. Browse Unique Stock.

Update; finished table

Posts

Update; finished table

#1

Update; finished table

James Watriss

>Finally done.

Brown English oak on top of a stained base made of euro beech.


img

Re: Update; finished table

#2

Re: Update; finished table 

James Watriss

>


img

Re: Update; finished table

#3

Re: Update; finished table 

James Watriss

>


img

Re: Update; finished table

#4

Re: Update; finished table

James Watriss

>Long story short, My girlfriend and I took a road trip to PA to visit the Nakashima studios, among other things in PA, shortly after my wrapping up at NBSS. I found this board at Hearne hardwoods later that week. Hearne is a wonder to behold, highly recommended to anyone passing through the area. I wasn't exactly sure how I'd use it, but I could tell it was going to be a cool table top at the time. And after I bought it, it literally stayed wrapped in shrink wrap until I started this project. It sat in the stairwell at my old apartment for months, finally migrating to my first shop... and eventually to the shop I have now. And finally, I pulled it down 2 weeks ago.

Re: Update; finished table

#5

Re: Update; finished table 

James Watriss

>


img

Re: Update; finished table

#6

Re: Update; finished table

Bruce, a MN Galoot

>The table is as spectacular as your joinery. Well done!

What finish did you use?

Bruce

Re: Update; finished table

#7

Nice contrasts

Bill Houghton, Sebastopol, CA

>the "wild" table top with the very controlled, linear trestle base.

the lively grain with the dour dark base colors.

Very, very nice table. I'll be happy to e-mail you my address for delivery.

Re: Update; finished table

#8

Ellis Walentine

Stop by next time, James

Ellis Walentine

>I've been known to proffer cold beverages and a bite to eat to wayfaring woodworkers. Not to mention good chat.

Cheers,

Ellis

Re: Update; finished table

#9

Re: Update; finished table

wilbur

>Really nice job! I hope to be able to make something half as nice, someday.

When you got the board for the top, was it completely split at the time, or was this part of a longer board?

Re: Update; finished table

#10

Re: Update; finished table

James Watriss

>Yes, it was completely split. This is the pith board of the tree, the crack is from the pith coming apart. There was a little bit of rotten and fuzzy stuff in the crack that I had to clean out, too. The upside is that the board is basically 100% quartersawn.

This is the board beforehand, having been wet down to show color, and raise the grain.


img

Re: Update; finished table

#11

Will do! :)

James Watriss

>

Re: Update; finished table

#12

Re: Update; finished table

James Watriss

>BLO, followed by a mix of BLO, tung oil, and turpentine, and then a few coats of waterlox varnish, and waxed.

Re: Update; finished table

#13

Re: Nice contrasts

James Watriss

>I'll start looking for packing peanuts. :)

Re: Update; finished table

#14

Inspiration

Bill Houghton, Sebastopol, CA

>I have a piece of oak - specific variety unknown - that's a similar slice through the pith. I picked it up at a garage sale years ago, never gotten around to doing anything - and, since my barn has grown increasingly open to the weather (a polite way of saying it's falling down), I'm not sure of its current condition.

Still, if it's there and not rotted, it could make a similar though not nearly as attractive table. Best get into that part of the barn this summer.

Re: Update; finished table

#15

Excellent job James!

Scott Burr sweating under the redwwod

>Thanks for the link to your blog, I see why you were scratching your head over the base. How did you attach the top?

That's a fine table IMHO.

Re: Update; finished table

#16

Jim in Burlington Ont.

Sad about the crack

Jim in Burlington On

>Just send it to me and I will fix that nasty crack for you