Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

This is the most versatile work station you will ever use

LV Scraper Plane Tips?

Posts

LV Scraper Plane Tips?

#1

LV Scraper Plane Tips?

Tony - Memphis

>I understand the learning curve on these things is steeper than the few minutes it takes to remove it from the box. I tidied up the blade last night and fiddled with it for a while without real good results. Any tips, ideas, comments, etc.?

Thanks,

Tony

Re: LV Scraper Plane Tips?

#2

Re: LV Scraper Plane Tips?

Alan Schwabacher

>The thing I found got me to the right setting quickest was to take the blade out and use it as a hand-held scraper. (I assume you've sharpened it already.) Note the angle to the work you use it. Now put it in the plane and set to the angle you found works. Fine tuning from there should be a lot easier. Bowing the blade just a touch is also useful. Once you get it set, it's great.

Re: LV Scraper Plane Tips?

#3

Re: LV Scraper Plane Tips?

ThomD

>Once you have the angle you want to work it at. Drop the blade so it rests on the work, then tighten it in. It is now correctly referenced to the wood. observe adjustment of the angle for the direction that drops the blade deeper, and use the angle adjust for final depth of cut. That's just general info, not specific to the LV, but it works with my various scraper planes, Except the Japanese ones. I still normally reach for the hand scrapers, for most stuff.

Re: LV Scraper Plane Tips?

#4

Jim in Burlington Ont.

Glass plate

Jim in Burlington On

>I set the plane on a glass plate and install the blade. Then just like when planning you turn the bow screw a little at a time until you start taking shavings. The blade tilting device is really a crap shoot and I don't often adjust that. You also need several pratice cut offs to get the perfect scraped surface.

Re: LV Scraper Plane Tips?

#5

Re: LV Scraper Plane Tips?

Wiley Horne--So. Calif.

>Hi Tony,

Which of the LV scraper planes do you have, the small or the regular large size?

The thing i have experienced is that if I'm not getting the right shavings, it's because of an angle mismatch, and usually that I've put too tight of a curl on the hook, so that the blade wants to work at a lower angle than the plane allows (or that I've got the plane set for).

So I agree with Alan and Thom's approach about getting the angle right first. Which is why it matters if you have the small or large LV scraper--the small has a fixed bed angle. If you have the small plane, just take the blade out of the plane and see what angle it wants to cut at, and if it's very far off 20 degrees from vertical (the plane's bed angle) then that's the answer.

Wiley

Re: LV Scraper Plane Tips?

#6

Thanks

Tony - Memphis

>I went out and fooled with it another hour or so last night. I'm still not getting anywhere. I am only getting scraping on one side of the blade. I started over with my sharpening and left the burr off just to see if maybe I was making an uneven burr. Tried scraping by hand to get the angle, using a sheet of paper, etc. Nothing seems to work. If this thing is that fussy, I'm sending it back. I've read some other reviews where folks reported that they didn't use them much as a result. That's too much money to collect dust just because it is too hard to use. Wish I had asked for something else for my birthday! Oh well.

Thanks for the help.

Tony

Re: LV Scraper Plane Tips?

#7

Re: LV Scraper Plane Tips? *LINK*

Steve McDaniel

>WoodCentral has an article on setting up this scraper. It might help.


Wood Central Article on LV Scraper Plane

Re: LV Scraper Plane Tips?

#8

Re: LV Scraper Plane Tips?

Tony - Memphis

>Thanks. Hadn't seen that. Sounds like I tried the same things and still didn't get anywhere. Very frustrating!

Tony

Re: LV Scraper Plane Tips?

#9

Update

Tony - Memphis

>Well, still no progress, but a gentleman from Veritas is trying to walk me through the process and figure out what I am missing before I pack it up and return it. Wish me luck. I have a nice piece of curly maple that will soon be a top for a tea table that i was hoping to smooth with the new toy.

Tony