Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Abingdon, VA – Tree Cutting & Portable Sawmill

Sanford Uni-Ball Power Tank Pens

Posts

Sanford Uni-Ball Power Tank Pens

#1

Sanford Uni-Ball Power Tank Pens

Alan DuBoff

>I have to say, it is not often you run across a product that just works so good for a given task that you become very fond of using them.

What is unique about the Power Tank is that the pen is pressurized and you can mark at any angle. Fisher sold a space pen that some folks may remember, you can still get those in some places also. Those were used to go to the moon during the 60s...not to digress, you can still get those pens as well, but these Power Tank pens are uni-ball pens, and as such the ink does flow nicely.

In the U.S. they only seem to sell the 1.0mm ball (bold), which produces a .4mm line. However, in Japan they have ones that are .7mm ball, and they are a fine point, I just got some of these fine tip pens, turns out the Japanese use them for writing Kanji as the tip is small and the ink doesn't blot on the characters. At least how I understand it. You can buy these online. Easier to find the 1.0mm ball, they sell those in the U.S. All come in Black, Blue and Red.

Not only do they mark in all directions, but they will mark on wet wood also. This is handy if your working in the rain, or if you mark something that is sitting in the rain.

The red is nice in case you make a layout mistake...the color stands out from the original marking.

Anyway, I typically use a ball point pen for marking out dovetails on furniture, and mortises and such, but will be using these now.

It must be a Power Tank to be pressurized.


img

Re: Sanford Uni-Ball Power Tank Pens

#2

size question

Bill Tindall, E.TN

>I am fond of gel ink for wood marking but finding a format that does not run on wood is difficult. If I understood these don't run/blot. But, do I understand that you use a .7 mm for dovetail marking? Typically, a .7 makes a line on wood wider than I consider suitable for precise sawing. Please clarify.

Re: Sanford Uni-Ball Power Tank Pens

#3

Re: line widths and dovetails

Dave Mount

>This is not at all rant at Bill, and I apologize if it ends up hijacking the thread, but I've never understood the concern over line widths in the context of cutting dovetails. I mean, you cut on the waste side of the line, what does it matter how wide the line is?

In my world, the important mark is the edge of the line, not the line itself. The only requirement of a dovetail marking instrument is that it's small enough to fit in where it needs to go, and is constructed/sharpened in a way that allows the business end to be placed tight up against the piece you are marking from. I think I could cut dovetails just fine marking them with a full width line from a carpenter's pencil, as long as the edge of the lead could get right up against the piece I am marking from. Sawing to dovetail marks you're leaving the lines, not splitting them.

Related to this, I've never understood those who assert that you can only cut dovetails accurately when they are knifed in. Sure, I get that this is a tool well suited to being laid right against what you are marking from. Marking a baseline, a precise length or delineating a tenon shoulder -- a knife is great. But for marking dovetails, it just gives me a mark I have to subsequently darken in order to see it well (maybe that's a personal problem with my eyes). I guess if one frequently pared the cheeks of pins/tails, using a knife would help register the chisel, but I shoot for a fit right off the saw and only pare if I've screwed up.

For me, a mechanical pencil is well suited to marking dovetails. I use a 0.5mm not because the line is fine, but because it's narrow enough that normal use keeps the bottom of it more or less flat, which is what you want (so it is marking right up against the edge). The kind I use has a very slim tube that extends beyond the main barrell and that combined with extending the lead a little more than is typical gives a fine tip that is easy to reach into tight places.

Sorry to be a little "ranty" -- this just always seems to me to be an area where there is more smoke than fire.

In fairness to Bill and back to the original post, I guess a 1mm ball making a 0.4 mm mark would be intrinsically marking 0.3 mm away from the ideal mark (in the context of a dovetail), and a smaller diameter ball would reduce that. A mechanical pencil doesn't have this problem, though I admit graphite pencil can be hard to see on walnut.

I'll also allow that if one is stringently following period methods, a 0.5mm mechanical pencil, or any fine tipped pencil, may be out of bounds. If a sharp pencil is not at hand, a knife would be a logical method.

Dave, who's really in a better mood than the above would suggest.

Re: Sanford Uni-Ball Power Tank Pens

#4

Re: size question

Alan DuBoff

>Bill,

The fine point tip (.7mm ball) is a fine line. That is the size of the ball, not the size of the line. They are definitely fine point pens. I do not know what the size of the line is on these.:-(

The bold tip (1.0mm ball which makes a .4mm line) is a noticeably fatter line.

The .7mm ball is a great pen for marking and doing layout of joinery on all woodworking, speaking for myself. Look up ebay auction 300324975056 for the fine point pens (.7mm ball).

Regards,

Alan

Re: Sanford Uni-Ball Power Tank Pens

#5

Re: line widths and dovetails

Alan DuBoff

>Dave,

I often use a Stanley utility knife that has a v-shaped edge on it. Some here have asked me how I overcome the fact that the mark I layout will not be proper, and that it will be impossible to get the blade to register in a straight edge properly.

I don't know what to say, I'm a lesser craftsman knowing I use a v-shaped blade, but don't let it bother me.

I layout my dovetails like Rob Cosman, he marks the points with a set of dividers and then uses a pen in the indentation to register the straight edge against. Put the tip inside the indentation first, then place the straight edge up against the pen tip. It works for me.

But I do use the Stanley 10-049 utility knife for layout and markup for joinery...I guess I'm a lesser craftsman for that. I honed the top round, as Rob Cosman suggested in one of his videos, but he uses another type of Stanley utility knife that is older. It is also a v-shape edge, go figure...if my joinery started looking like Rob's, that certainly wouldn't be the end of the world...*lol*

Regards,

Alan

Re: Sanford Uni-Ball Power Tank Pens

#6

Re: I agree, go with whatever works fer ya

Dave Mount

>

Re: Sanford Uni-Ball Power Tank Pens

#7

I'll give it a try

Bill Tindall, E.TN

>My sawing precision is limited by how well I can see where I am sawing. I am a great fan of ink on walnut. Much easier to see than any other marking technique. I can't reliably see scribe lines unless light is perfect but I can see a gel ink line under any light.

In reply to Dave, for what ever reason I cut more precisely to a fine line than a fat one in spite of the fact that your argument makes logical sense. After some more than 100 DT drawers I have become set in my ways and unwilling to learn to cut to a fat line.

Re: Sanford Uni-Ball Power Tank Pens

#8

Re: line widths and dovetails

Derek Cohen (in Perth, Australia)

>Hi Dave

There is a good reason for knifing lines when marking dovetails.

I agree that in the initial marking of lines it does not matter about the thickness of the line drawn. In fact - as Frank Klaus demonstrates - you do not need a line at all.

The important line is that one drawn from the "template" you create when you make the first side of the dovetail pair. If your pins or tails are widely spaced, such that you can get a pencil or pen into this comfortable, then again there is no big deal about the thickness of the line.

It is only when the pins are narrow and a pencil/pen cannot get into the space that a knife is required.

Can your pen do this? .............. :)


Regards from Perth

Derek

Re: Sanford Uni-Ball Power Tank Pens

#9

Re: line widths and dovetails

ThomD

>"I mean, you cut on the waste side of the line, what does it matter how wide the line is?"

Not true a lot of people split the line )in which case leaving a piece of inky line behind would be a problem).

I do agree with your idea that line width doesn't mater in any abosolute sense. When you go to place a bullet on a 100 yard target, the front sight may cover feet of it up. The front sight just represents something that has a relationship to the impact of the bullet. What that relationship is comes down to the task at hand and the way the user likes to work. There is little in the way or real relationship between any of these lines and where the saw goes. If drawing a certain type of line gets the saw cut where it needs to be, and in the process of transferring the line you set up to get the mating cut in the right place, that is what the job calls for.

When I transfer the lines I use a pencil that has just started to round over, and I sand it to an elipse. This gives me a knife's edge line flush to the edge of the first joint. I then saw that line in half, which technically ought to mean the joint is loose, but it is perfect. Just how it comes out for me after a bit of practice. I also scribe some lines on very fine joints in hard and dark woods.

The correct way of thinking about it is as aiming. If one is accumulating lines and cuts from each other, with 2 sets of lines and two sets of cuts, a lot of eror starts to accumulate. In aiming the lines aren't describing the edges of the joints, they are an aid to sighting the cut.

Re: Sanford Uni-Ball Power Tank Pens

#10

Re: line widths and dovetails

Dean J in MN

>Can your pen do this

You know, if you just cut dovetails the "right way" you don't need to fit your marking apparatus into a small opening. :)

I'm a tails-first dovetailer for most work, but if you really want tiny pins, cut them first and you can lay out the tails with a crayon! :)

-Dean

Re: Sanford Uni-Ball Power Tank Pens

#11

agree with Dave

John Pappas

>