Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

This $39 jig will make you a WOODWORKING GOD!

Amputation pocedure?

Posts

Amputation pocedure?

#1

Amputation pocedure?

Edward in Vancouver

>For chair legs that is.....

Recieved orders to cut down the legs on several commercial bar-height chairs to match the height of their lower, dining room height siblings. Both chairs are made by the same local company specializing in restaurant chairs and tables. Save for the height, or length of the legs, both styles of chairs are otherwise identical.

My thoughts ran to the following procedure:

As the front legs are plumb and the rear legs splayed, I thought of measuring the front legs, and using a saddle square, marking off on all four sides. Then, with a 3' level, bringing that mark across to the rear legs. Using a bevel guage, I can make my mark on all four sides of the leg. Then cut.

I am unsure if this is a good way or not.

Like a real operation, once the legs are cut there's no going back, and I am hesitant to make that cut untill I am sure that the marking "procedure" works....

Suggestions? Please?

Re: Amputation pocedure?

#2

Just an idea

Bill Houghton, Sebastopol, CA

>Set up one of each chair - the high ones and the low ones - on a level, flat surface, making sure the seat's at its proper angle to the floor both ways (if you're lucky, the edges of the seat will be level when this is true). Measure the distance from the seat edge to the floor on both chairs, using the exact same reference point on each (e.g., right front corner). Subtract the lower chair height from the upper. You now have the amount you have to remove from the legs of the upper chair to make it match the lower one.

Make a "stand" the proper height, on top of which you can set a pencil, extended as much or as little as necessary to reach the leg. Now move that around each leg, marking it. Cut. Sand and finish.

I would consider making a stand an inch lower, too, to test the approach on one chair. Mark from both stands - the full height one and the lower one - then cut at the lower mark. If my theory is correct, you should then have a chair that's just fine, except one inch too tall. If my theory's wrong, you can still salvage that chair with some other approach.

When I was young, tailors all had hem-marking rules that worked on a similar principle, with a height-adjustable nozzle that sprayed chalk when the tailor squoze a bulb. The woman whose dress/skirt needed adjusting would stand perfectly still (in her best finishing school posture) while the tailor moved around her, spraying chalk on the skirt at the desired height.

Re: Amputation pocedure?

#3

Jesper, Denmark

Re: Amputation pocedure?

Jesper, Denmark

>Measure the height difference. Set this dimension on a pair of compasses. Mark each leg with the compasses from the floor.

If the back legs are only splayed back, you can cut both legs on one side with a sled on the table saw.

Re: Amputation pocedure?

#4

Re: Amputation pocedure?

Edward in Vancouver

>Thanks! Those methods sound a lot better than futzing around with levels and bevel guages.

Re: Amputation pocedure?

#5

Re: Amputation pocedure?

Charles

>Prepare a block the exact thickness of the length you need to remove from the legs. Set the chair in its normal position on your workbench. Slide the block up to each leg and register a pencil off the block and mark to your heart's content. Saw the legs off with a tenon saw leaving half the line.

If the back legs are already a little shorter to give the chair 'slouch' the block you prepared above will maintain that relationship between the front and back legs while bringing the whole she-bang down to the height you need.

Dividers will work but the marking is not as easy as when you use a simple block of wood and a No. 2 pencil.

Good luck.

Re: Amputation pocedure?

#6

Re: Amputation pocedure?

Marv

>I've used the block method. It works sorta like a height gage. If you have access to or happen to own a height gage, it would be the most accurate method to use. You can scribe a fine line both inside and outside of each leg. After you shorten the legs, radius or champfer the edges.

Marv

Re: Amputation pocedure?

#7

Squoze? You made my day.

Chuck Nickerson

>

Re: Amputation pocedure?

#8

Yes Block is good

Roninkokomo

>It does one of two things. Minimizes the likelihood of error in making four separate measurements exactly alike, or it standardizes incompetence ( If you screw up, all legs will be wrong the same way)

Re: Amputation pocedure?

#9

Re: Squoze....defined...Googled

Marv

>Definition of squoze :.

(skw�z)

1. (v.tr.) To have squeezed something previously. The past tense of squeeze.

Example: Yes, I squoze it as hard as I could.

Re: Amputation pocedure?

#10

Re: Squoze? You made my day.

R.J.Whelan - Sierras, California

>First time I ever heard/saw this word was:

President Reagan had a tiny skin cancer on his nose and he said "... I just squoze it ...". At the time I didn't know it was a real word, but I figured if it was good enough for the President, it was good enough for me - been using it (the word) ever since ... rj

Re: Amputation pocedure?

#11

Re: Amputation pocedure?

R.J.Whelan - Sierras, California

>I recently cut down 8 chairs for a client (removed 1.25"). Since I had to do this 32 times I decided to make a jig.

Glued two pieces of plywood together - about 8" x 8" and planed them to 1.25".

Drilled a hole about 1.5" diameter through the block

Made three spacer blocks that were 1.25" thick + the width of saw kerf.

Place chair on a flat surface with one leg through the hole in the jig.

Lay cross cut saw on jig and saw through leg.

Move jig to next leg and place spacer block under the leg just cut to level and support chair. Cut leg #2

And so on ........

I think it might have taken me 30 minutes to build the jig and another 2 hours to saw all 32 legs and plane a chamfer on each.

My 2 cents - FWIW ........... RJ

Re: Amputation pocedure?

#12

I never figured it for a real word

Bill Houghton, Sebastopol, CA

>and am abashed to discover it is.

Re: Amputation pocedure?

#13

Excellent thinking through of the whole process

Bill Houghton, Sebastopol, CA

>Saves marking and supports the leg while cutting. Very, very clever R.J. That high mountain oxygen is clearly good for the brain.

Re: Amputation pocedure?

#14

Abashed Definition

Marv

>abashed

adj : feeling or caused to feel uneasy and self-conscious; "felt

abashed at the extravagant praise"; "chagrined at the

poor sales of his book"; "was embarrassed by her

child's tantrums" [syn: chagrined, embarrassed]

Re: Amputation pocedure?

#15

Re: Yes Block is good

Charles

>All the precision instruments are just a touch too inorganic for me most of the time.

Can't get much simpler than a block of wood measured off a folding rule.

Re: Amputation pocedure?

#16

Squoze or Squozed...

Scott Burr in Ben Lomond, CA

>The past, past tense. If I may use it in a sentence. I was lonely last night and I squoze it...

RED CARD!

Re: Amputation pocedure?

#17

Re: Excellent thinking through of the whole proces

chuckbeck in cent il

>Yep, jig blocks work great like this. I have to cut down piano benches on the spot quite often and I keep a group of 3 blocks 1/2" tall and a group of 3 blocks 1" tall. A couple strokes on each leg, chamfer, and go sit at the piano.

Re: Amputation pocedure?

#18

good stuff rj

roninkokomo

>

Re: Amputation pocedure?

#19

Ellis Walentine

How would this work?

Ellis Walentine

>I've never used this method, but it seems like it would work very well. Figure out how much height you want to lose, put a washtub on a flat, level surface with a piece of slate or something in it to serve as a reference surface. Fill the tub with water so the depth of the water above the slate is exactly equal to the height difference. Then set the chair/stool in the water, pull it out and cut on the waterline.

Ellis, way out of the box

Re: Amputation pocedure?

#20

Re: How would this work?

Warren in Lancaster, PA

>Ellis, I was tempted to suggest this method last week as a joke. Add a whole packet of aniline dye to the water.

Re: Amputation pocedure?

#21

Leave the chairs... drill holes in the floor.

James Watriss

>What we do is screw a board to the bottom of the plumb legs, and run that against a fence on our huge bandsaw. Fence is set to the length you want removed.

No marking required.

Re: Amputation pocedure?

#22

Re: How would this work?

Alex Grigoriev

>No. Mix a bucket of epoxy, pour it to a pan and set the chair into it. When it hardens, cut the legs at the epoxy surface. Mortar works, too.

Re: Amputation pocedure?

#23

"Mortar works, too."

Bill Houghton, Sebastopol, CA

>And, if you never liked the chair in the first place, you can sink it in the nearest harbor.

We're getting a bit out there. Has anyone mentioned a laser level yet?