Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Portable Sawmill & Tree Service – Abingdon, VA

Behlen's "Rock Hard Table Top Varnish."

Posts

Behlen's "Rock Hard Table Top Varnish."

#1

Behlen's "Rock Hard Table Top Varnish."

Craig Jahr

>In the message string below, RJ recommended Behlen's "Rock Hard Table Top Varnish." Is this applied by brush or padded on? Do you thin the product? Are witness lines a problem when you rub it out? I have a 40X80" dining table that I padded with dewaxed shellac because of ease of application and it rubs out really nicely but I found (I was warned) that shellac isn't tough enough for a dining table. Once I fix the shellac, I need a tougher topcoat. On a table this big, will Rock Hard Table Top Varnish be difficult to apply (I don't have spraying equipment)? Any suggestions greatly appreciated. Many thanks.

Re: Behlen's "Rock Hard Table Top Varnish."

#2

Re: Behlen's "Rock Hard Table Top Varnish."

Warren in Lancaster, PA

>I think varnish is the choice most would make. I like a natural bristle brush and I apply varnish as it comes from the can. Since you are willing to rub it out, dust specks are hardly a problem.

I don't know what your problems were, but I find shellac to be extremely tough and durable. It has two weaknesses: it is vulnerable to hot pans (like from the stove or the oven) and also to alcohol. One of its strengths is ease of repair and renewal. It can almost always be freshened up without removing and starting over. It does not seem to deteriorate over the decades like some varnishes. And it is more handsome.

Re: Behlen's "Rock Hard Table Top Varnish."

#3

Re: Behlen's "Rock Hard Table Top Varnish."

Craig Jahr

>Thank you, Warren. I'm not exactly sure what caused the damage. It's localized to where the two usual place-settings are, but we do use place mats. Also, the laptops are used in those places but they only gently warm the table surface. No alcohol spills. I've tried to damage a shellacked test board by setting coffee mugs containing boiling water in a puddle of hot water but even that didn't do much damage surprisingly. I think I'll take your advice and touch up the shellac and ban the laptops because, as you say, the shellac finish is beautiful and it's an easy fix. Thanks again.

Re: Behlen's "Rock Hard Table Top Varnish."

#4

Re: Behlen's "Rock Hard Table Top Varnish."

Bill Tindall, E.TN

>I have not used this product but most varnish is formulated to pass EPA inspection,not for ease of application. I find that I have to thin the urethane varnishes to get them to level properly.

If you are seriously into woodworking use this opportunity to buy spray equipment.

Re: Behlen's "Rock Hard Table Top Varnish."

#5

Thank you, Bill. NM

Craig Jahr

>

Re: Behlen's "Rock Hard Table Top Varnish."

#6

Re: Behlen's "Rock Hard Table Top Varnish."

RJ Whelan

>Craig ... I use varnish because 95% of my work is for customer use and I have no way of controlling the care it is given - in many cases the sale is through a gallery and I don't even have an opportunity to speak with the buyer. I have printed up a "use and care" instruction sheet, but I don't know if they are provided to the buyer.

I use a Badger brush to apply the finish and try to avoid temperatures below 55 or above 85. The first two coats are thinned about 15% (1:8) and I don't rub out between coat 1 and 2 (unless I have a lot of dust or raised grain: this gives me a fairly thick coat to work with. After the first coat I rub out with 400 (stearate paper); after coat three (full strength) I go to 600; coat four is rubbed out with 1200; coat five is 1200 (if additional coats are going to be applied) or steel or bronze wool in the case of #5 being the final coat. I allow a full day between coats. I try to wait a couple of weeks to rub out the final coat (steel wool) and apply a coat of paste wax and then power buff with a lambs wool bonnet.

Good luck ... RJ

Re: Behlen's "Rock Hard Table Top Varnish."

#7

Re: Behlen's "Rock Hard Table Top Varnish."

Craig Jahr

>Thank you, RJ, for all the detail. I'll try the varnish on top of shellac on a scrap first. It sounds as though the varnish doesn't dry so fast that overlapping brush strokes is a problem.

Re: Behlen's "Rock Hard Table Top Varnish."

#8

Re: Behlen's "Rock Hard Table Top Varnish."

RJ Whelan

>Craig ... it flows out pretty well, unless the temperature and humidity are high/low. In warm weather I will sometimes put the varnish in my shop refrigerator for about 10-15 minutes before I start brushing - this extends the open time by a bit.

This product sands well (powders nicely) if you use stearate paper (I get mine from Klingpor).

RJ

Re: Behlen's "Rock Hard Table Top Varnish."

#9

5 coats?

Bill Tindall, E.TN

>I have not use this stuff but 5 coats of typical (urethane or alkyd) varnish seems more than necessary to get an acceptable build. I only put 3 coats of varnish on a floor. Is this varnish especially thin, low solids?

Re: Behlen's "Rock Hard Table Top Varnish."

#10

Re: 5 coats?

RJ Whelan

>Bill ... most of my woodworking is customer work: not knowing the amount of wear a table top, dresser top, etc will receive, I err way on the side of caution.

As a matter of fact, I have to redo the top of a Parson's Table that's been sitting in a gallery for a couple of years (2 coats of shellac and three coats of Minwax wipe on poly). Apparently they used the table pretty harshly, because it's all but unsellable in it's current condition. I'm going to sand it with 400 and put at least 2-3 coats of additional poly on it before taking it to the new gallery.

Five coats is my minimum: coat 1 & 2 are really more like a single coat as I thin them pretty agressively; the idea being to get a good, faily thick film before the first rub out with fairly coarse (400) paper.

Most of my finishing is self learned (with a little reading thrown in) and this is what seems to work best for me (with this product).

RJ