Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

This is the most versatile work station you will ever use

"Donar body" for a scrub plane?

Posts

"Donar body" for a scrub plane?

#1

"Donar body" for a scrub plane?

Edward in Vancouver

>Since most of the wood I use is salavaged, I like to give it a swipe or two with a scrub before I start machining it. My scrub up to about a week ago was a wood transitianal Stanley that I received with a mismatched blade, chip breaker, and lever cap. I had to alter the newer blade to fit the original chip breaker, and gawd knows where the lever cap came from. As a scrub, it performed OK. In any case, about a week ago I hit a buried headless nail in some white oak palletwood and cracked off the rear tote. Don't have time to make a new tote, and don't think I can repair the original.

I do have a "Handyman" #5, circa early 60's?, hardly ever used (wonder why?) that I've been eyeing as a likely candidate.

Would this be a decent candidate for a scrub?

Re: "Donar body" for a scrub plane?

#2

Re: "Donar body" for a scrub plane?

Alexander Grigoriev

>I didn't know the scrub plane needs a chipbreaker.

Re: "Donar body" for a scrub plane?

#3

Re: "Donar body" for a scrub plane?

chuckbeck in cent il

>I did basically the same thing with a crapsman 9" plane and I just pull the chipbreaker back off the edge 12mm or so. Works just fine, but it took a while at the grinder to get the heavy camber. Free is always good.

Re: "Donar body" for a scrub plane?

#4

Jim DeLaney, Austintown, Ohio

Re: "Donar body" for a scrub plane?

Jim DeLaney, Austintown, Ohio

>The wider the plane, the more work it is to take the big bites that are the usual with a scrub. That's probably why the Stanley #40 is only about 1�" wide.

Your #5 will work well, but a #3 would likely be better. I had one (traded it off) that was made from a #78, and it worked really well, too.

Jim D.

Re: "Donar body" for a scrub plane?

#5

Re: "Donar body" for a scrub plane?

Dean J in MN

>Considering a #5 is roughly the same length and width as a wooden fore (jack) plane, and a fore plane was the first plane to hit the wood in the 18th C I think a #5 is ideal. #40's are too narrow and too short to be used as a fore plane in my opinion.

Camber the blade, open the mouth to allow passage of the shavings and you have the ideal tool for the job.

-Dean

Re: "Donar body" for a scrub plane?

#6

Re: "Donar body" for a scrub plane?

ThomD

>I like wooden scrubs better than metal ones, and can make one in about 45 minutes, if I have the blade already.

Re: "Donar body" for a scrub plane?

#7

Re: "Donar body" for a scrub plane?

Roy Anderson

>A coarse set Jack with a deep camber blade makes a good plane for roughing in stock. I keep one set and ready for just such a purpose. I don't know if a HandyMan will take the abuse, since they have very thin blades, if I recall. See if you can fit in a standard Stanley blade. One thing's for sure, you won't hurt anything important by trying.

Re: "Donar body" for a scrub plane?

#8

Re: "Donar body" for a scrub plane?

Edward in Vancouver

>Thanks for the information, gentlemen.

I haven't gone down the slope with wedged planes yet, and a scrub sounds like a good project, however I have a loooong list of "to do" projects, so a home made wedged scrub will have to wait for a bit.

Actually, the iron on the "handyman" and the iron on the (short and well used) "sweetheart" iron that came with the transitional appear to be the same thickness. The #5 body is cast with "made in Canada" and has a real wood, albeit painted black tote and front knob. It was a gift and as near as I can tell, bought circa early 60's-- it also came with a "handyman" brace too(Yech... that one is behind the freezer....)

I do have a #78, but can't as of yet scare up an extra blade to grind a pronounced camber on.

Actually, I can swap out the "sweetheart" iron into the #5--once I grind out that nasty ding I put in it when I hit that hidden nail...