Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

If you sell to woodworkers, your customers are already here

Now I remember why I chose the LV small router

Posts

Now I remember why I chose the LV small router

#1

Now I remember why I chose the LV small router

Bill Houghton, Sebastopol, CA

>over eBay'ed Stanley 271s - a slightly grubby one went yesterday for $3 below the LV price.

I had posted about my experience of having the cutter twist on my LV plane. LV customer service recommended that I clean off the preservative oil on it. A little mineral spirits, followed by a little denatured alcohol to clean up any residual oiliness from the spirits, made a huge improvement. I then sanded both the cutter shank and the cutter beds with 80 grit sandpaper, which helped another 5-10%. If I still find myself having difficulties, I'll try the rosin trick suggested in the earlier thread (or coarse grit diamond paste, rubbed to embed in the cast iron?).

I do think Rob's elves should machine the cutter bed more coarsely, or reshaped the cutter shank for a more positive relationship to the cutter bed.

Re: Now I remember why I chose the LV small router

#2

Re: Now I remember why I chose the LV small router

Paul M. in San Diego

>I had an old 271 that came with a completely bunged up cutter. I tried to sharpen that little bugger but I never was able to get it to work well. I just gave it to a fellow student in my woodworking class who said he needed a small router plane. He works in a metal shop so he'll be able to figure out how to turn that pathetic cutter into something usable. I didn't need it anymore since I replaced it with the small LV router plane which works wonderfully!

Re: Now I remember why I chose the LV small router

#3

Re: Now I remember why I chose the LV small router

Derek Cohen (in Perth, Australia)

>Hi Paul

Sharp blades are everything!

The trick with router plane blades is to give them a slight hollow grind. This makes is easier to register the bevel face on a (e.g.) waterstone for honing (since the fixed blades must be done freehand and upside down).

Regards from Perth

Derek

Re: Now I remember why I chose the LV small router

#4

sharpening

paul womack

>Fortunately, having got them sharp, they stay sharp for a long time, since routers are normally used for finishing cuts, which is light work.

BugBear

Re: Now I remember why I chose the LV small router

#5

That's why I looked for a Record 722 :@)

wilbur

>They're cheaper, even if you buy them from overseas, and they have a nicer blade holding mechanism than the Stanley 271's. (Thanks, Paul!)

:@)

Re: Now I remember why I chose the LV small router

#6

exactly

Paul M.

>Starting with a correctly formed cutter, I can keep it sharp forever. But the 271 started with a blade that looked like it had 4-5 different bevels and a flat on the bottom that was way off from perpendicular. That was way too much work for someone without the proper jigging to restore such a tricky blade to proper shape.

Re: Now I remember why I chose the LV small router

#7

sharpening

paul womack

>That was way too much work for someone without the proper jigging to restore such a tricky blade to proper shape.

Proper jigging you say?

here's my take

And a semi-independant review of the results here

BugBear

Re: Now I remember why I chose the LV small router

#8

Sharpening router blades without a jig

Derek Cohen (in Perth, Australia)

>I would say that there are only two jigs I know of which you might use to sharpen router plane blades. One is Bugbears' and the other is Gary Blum's. More on the latter at another time.

To hone a router plane blade by hand is terribly easy and should take but a few seconds once the preparation work is done. Here are the steps.

Firstly, you can see that the blades come with a flat grind ..



Your first task is to add a hollow grind. You can do this on the end of a stationary belt sander, with a rotary drim on a Dremel, or with 80 or 120 grit sandpaper wrapped around a dowel.

The hollow can be fine, like this ..



Or marked like this (overexuberant) one ..



Next just balance the blade on the hollow



and freehand it sideways, like this ..



I use 1000/5000/12000 Shaptons.

Just a couple of swipes on each stone and you are done.

Regards from Perth

Derek

Re: Now I remember why I chose the LV small router

#9

Played with them both. I'll take the 722 also...

Scott Burr in Ben Lomond, CA

>They even included a box with mine :^)

I have way too many of these little things, but they keep following me home!