Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

REAL MILK PAINT

Bedrock 608C Refurb

Posts

Bedrock 608C Refurb

#1

Bedrock 608C Refurb

Dominic in Buck's County PA

>Hi Everyone!

Well here it is! Another in a series of Bedrock restorations!

I got this Bedrock 608C off of Ebay some time last summer for the princely sum of $80 (GLOAT!). The tote and knob were in pretty nice condition and the japaning looked reasonably intact. The iron was just about full length and looked to have never been honed! The body was sort of tarnished on the outside (which was not much of a problem) but the frog, chip breaker, and iron were pretty gummed up with rust and what looked and smelled like 100 year old pine chips.

Before:

Photobucket

Photobucket

Photobucket

Photobucket

I soaked the iron parts in Evaporust (which by the way was the same bottles I used on my last two planes and is now pretty much spent) and then wire brushed all the parts. It wasn't until I started cleaning the iron that I got a couple of surprises. As I was wire brushing the sides I found the old owner's initials stamped cleanly on both sides. As I was cleaning the iron I also found the Sweetheart mark!

After:

Photobucket

PhotobucketPhotobucket

The very light line along the sides was the result of soaking in Evaporust and not having it totally submerged. I could have sanded it out but figured that it really didn't bother me enough and the sides looks good just as they are.

Once I ground the primary bevel and honed the iron, I then tuned up the chip breaker and took this monster for a test run on some rough sawn Walnut. I fully expected this to be one of those planes that you use only when you need the mass and length of a big jointer. I thought it would be too heavy to use all the time. However, the ease that this plane went through that walnut was nothing less than jaw dropping (for me at least). And the shaving I was able to get was,...well you take a look!

Photobucket

Actually I shouldn't have been so surprised. I had a similar experience when I tuned up my Bedrock 606. All in all this was one of my favorite refurb projects and really showed me what a nicely tuned Bedrock could do. Whenever practical, this'll be my go to jointer!

Thanks for viewing!

See ya around,

My Avatar


Dominic

Re: Bedrock 608C Refurb

#2

Re: Bedrock 608C Refurb

Jim Shaver - Oakville, Ont

>Saint Dom Saves another one!!

The Temple is filled with smart looking Bedrocks Buddy, You Rock!!

take care,

Jim

Re: Bedrock 608C Refurb

#3

Re: Bedrock 608C Refurb

wilbur

>Excellent job, as always!

You sure that tool cabinet of yours is big enough? Sometimes I think it would be easier to compile a list of planes that you haven't restored. :@)

Re: Bedrock 608C Refurb

#4

Oh, I have THAT list!

Dominic in Buck's County PA

>Wilbur,

You wrote:

"You sure that tool cabinet of yours is big enough? Sometimes I think it would be easier to compile a list of planes that you haven't restored. :@)"

Yeah, they all fit. With a bit of room to spare for those upcoming LV planes! I'm all set to order that new little scraper! :>)

Oh, I have that list ALL ready! I actually have an Excel Spreadsheet that inventories my planes and shows the status (New, Needs Refurb, and Refurb completed). I get a nerdy little kick when I can change the status from "Needs Refurb" to "Refurb Completed"! :>)

See ya around,

Dominic

Re: Bedrock 608C Refurb

#5

Re: Bedrock 608C Refurb

Dominic in Buck's County PA

>Thanks Jim!

Re: Bedrock 608C Refurb

#6

You suck Dom! Congrats on a job well done!

Stuart Hough

>

Re: Bedrock 608C Refurb

#7

Re: Oh, I have THAT list!

Bob Demers

>Oh, I have that list ALL ready! I actually have an Excel Spreadsheet that inventories my planes and shows the status (New, Needs Refurb, and Refurb completed). I get a nerdy little kick when I can change the status from "Needs Refurb" to "Refurb Completed"! :>)

he he, that made me smile, 'cos I like to do the same.

I also do something similar in MS Words to track my reno progress, the 'highlite' of my day, is going over the 'To do' list and highlighting in Yellow what I have accomplished for the day.

It gives me a sense of accomplishment, while looking over my list and sipping a cold one :-)

Meanwhile in Excel, I track my reno cost, incliding the 'to buy' list which get changes to the 'bought' list as I go.

Oh, and I takes pictures as I go, and all my tools get the same 'computerized treatment' :-)

Bob, the nerdy Neanderthal

Re: Bedrock 608C Refurb

#8

Re: Bedrock 608C Refurb

Victor Parisian

>You suck!! $80.00 for a Bedrock 608-C? I bet you steal money from the paupers plate too. He he he!

Really nice job on that one. Keep up the posts. You inspire us all.

Victor - enjoying a rain soaked Easter Sunday in Houston

Re: Bedrock 608C Refurb

#9

'Nother nice one Dom!

Scott Burr in Ben Lomond, CA

>Well done as usual.

Do you see a noticeable difference between the older style (round sides) and the newer (square sided) Bedrocks?

Thanks for sharing, Scott

Re: Bedrock 608C Refurb

#10

Re: 'Nother nice one Dom!

Dominic in Buck's County PA

>Scott

Thanks for the compliment!

You wrote:

"Do you see a noticeable difference between the older style (round sides) and the newer (square sided) Bedrocks? "

Not really. I mean, they are both as solid as hell. But I find myself preferring the square sided ones for their ease of adjustment

See ya around,

Dominic

Re: Bedrock 608C Refurb

#11

Nice job!

roninkokomo

>I sure love my 608