Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Have a question? Ask Woody!

Oddball machine screw size

Posts

Oddball machine screw size

#1

Oddball machine screw size

Bill Houghton, Sebastopol, CA

>Does anyone know whether Stanley used either #14-24 or 1/4"-24 machine screw thread on any common plane? I'm trying to test thread pitch on a blind hole on a Sargent plane, and I think this may be the size/pitch.

Re: Oddball machine screw size

#2

Or

Bill Houghton, Sebastopol, CA

>does anyone happen to have a screw in either of these size/pitch s/he could loan me?

Re: Oddball machine screw size

#3

Jim DeLaney, Austintown, Ohio

Re: Oddball machine screw size

Jim DeLaney, Austintown, Ohio

>Stanley was infamous for 'inventing' their own thread sizes.

That said, try a metric M6 X 1 (6mm diameter, 1 thread per mm of length - or about a 25.4 tpi pitch).

Jim D.

Re: Oddball machine screw size

#4

Re: Oddball machine screw size

George Moore

>Bill,

Stanley used 12-28 threads for the tote and knob screws. The frog uses the same threads if I remember correct.

Sargents are a different thread.

George

Re: Oddball machine screw size

#5

threads *LINK*

paul womack

>Stanley used 12-28 threads for the tote and knob screws.

Unless it changed at some point, I don't think so.

I put some info up on my website a while back.

I'm as certain as I can be that it's #12-20

BugBear


http://www.geocities.com/plybench/tour.html#stanley_threads

Re: Oddball machine screw size

#6

Follow up

Bill Houghton, Sebastopol, CA

>David Barnett, in an e-mail, steered me in the right direction. It turns out older Harleys used 1/4"-24 cap screws in a lot of places. I found a local shop - well, guy - who was able to pull out a screw in that pitch. We confirmed that my Sargent plane indeed uses that size/pitch thread for the fence rod.

He informed me that this, and other offbeat thread pitches, were common on railroad equipment, and that some of Harley's founders were railroad folks, and may have made use of the tooling available to them as the company took off.

It's technically "1/4"-24 National Special." I guess when the national standards were established, the group establishing standards settled on National Coarse and National Fine and threw everything else into National Special. Kind of like my observation to a coworker years ago that every filing system, no matter how intricate, needs a "miscellaneous" folder.

Re: Oddball machine screw size

#7

threads *LINK*

paul womack

>He informed me that this, and other offbeat thread pitches, were common on railroad equipment, and that some of Harley's founders were railroad folks, and may have made use of the tooling available to them as the company took off.

Yeah, but did they *have* to use bits of track to make the frames from?!??!?

:-)

BugBear


http://www.geocities.com/plybench/tour.html#stanley_threads

Re: Oddball machine screw size

#8

OT - motorcycle speculation

Bill Houghton, Sebastopol, CA

>Perhaps it was an early attempt at vibration absorption through mass, like Norris planes.

Don't know; I rode a BMW. Staid, yes, but I didn't have to safety wire every fastener to keep bits from falling off while riding, idling, or parked; the rear view mirror showed me the cars behind me rather than a poor imitation of Van Gogh's "Freeway in Detroit"; I don't think I did any work on the electrical system while I owned it except the occasional bulb and ignition point change; and the motorcycle was not studying how to do an oil finish on every parking space - none of which could be said about the American or (ahem, Bugbear!) British motorcycles of the era.

Re: Oddball machine screw size

#9

Jim DeLaney, Austintown, Ohio

Re: OT - motorcycle speculation

Jim DeLaney, Austintown, Ohio

>Regarding Harleys...

About six or seven years ago, my SAE group (Motorcycle Committee, which I chaired) was touring the (Formerly Harrah's) Automobile Museum in Reno. Among the group were three engineers for HD.

Fantastic display of cars, both old and new, with many absolutely suberp restorations. When we finally got to where some bikes were displayed, there was a Harley Servicar (Think three-wheeled police bike - very common in the 1950's). Anyway, it was sitting there with a drip pan under it, and a small puddle in the pan. At that point, it occurred to us that the Harley was the ONLY VEHICLE IN THE WHOLE MUSEUM that had a drip pan under it. The HD guys took quite a ribbing over that!

Jim D.

Re: Oddball machine screw size

#10

Re: OT - motorcycle speculation

Pam Niedermayer, Austin, TX

>I decided to give "Buy America" a try in '78, so bought a new Harley cafe sportster instead of a BMW. It vibrated a lot, required a lot more muscle to muscle around (whereas the Beemer just seemed to go where I thought it should). Finally gave up on it when it started shaking itself to death while I rode down the road, parts falling off left and right. I lucked out, found a guy who "just had to have" a Harley cafe for some show or convention or other, traded him for a BMW cafe plus some money. Whew!

Pam