Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

This is the most versatile work station you will ever use

Crosscut Saw?

Posts

Crosscut Saw?

#1

Crosscut Saw?

Tony - Memphis

>I am looking to get a decent crosscut saw for rough cutting my long pieces of lumber. Sometimes, I buy lumber that may be 8-10' long and I cut it to rough length by hand. I don't have a good crosscut saw. I've been using a rip saw. Works, but it seems harder than it ought to be! I have an old Atkins that is pretty coarse (maybe 8 or 9 tpi?). I thought about just refiling it, but my other rip saw is pretty fine (not sure what tpi it is). Anyway, the economy is hitting us hard, so I don't have much allowance to spend. I'm definitely looking for a user, name/brand/etc. makes no difference to me. Oh, most of the stuff I cut is domestic hardwoods and some mahogany. Usually 4/4, but I do have some 12/4 that have to cut now and then. Thanks.

Tony

Re: Crosscut Saw?

#2

Re: Crosscut Saw?

Patrick Gibbons, Katy, TX

>8 or 9ppi is a good tooth count for what you're wanting. I finish cut with 10ppi usually. 9tpi is the same (usually) as 10ppi.

Re: Crosscut Saw?

#3

What I did

David Miller from Iowa

>This may well be blasphemy here, but I needed a saw for rough cutting so I went and got a new Stanley "shark" handsaw at the home center - cheap. It has a weird kind of teeth that are very aggressive (although can't be resharpened), cuts faster than a crosscut saw and also fits into my toolbox.

And, I hated the plastic handle so I stuck a panel saw handle on it and it is my "go to" saw for rough cutting


img

Re: Crosscut Saw?

#4

Re: What I did

Glenn Madsen near San Francisco

>You're right, David. It is blasphemy.

And an idea worth stealing! ;-)

Re: Crosscut Saw?

#5

Re: What I did

Wiley Horne--So. Calif.

>David,

That's an interesting saw. Western push saw with what looks like Japanese teeth. Couple of questions: What is the tooth count on the saw? And does each tooth have a third facet, up at the top of the tooth?

Thanks for showing,

Wiley

Re: Crosscut Saw?

#6

I guess we both are Dave...

Scott Burr in Ben Lomond, CA

>I have one of those. It cuts fast and pretty clean for the most part. I do have some trouble starting it in softer woods sometimes.

BTW, I'll be stealing your handle improvement idea.

Re: Crosscut Saw?

#7

Wiley, Here's Stanleys page in theses saws *LINK*

Scott Burr in Ben Lomond, CA

>Very similar to a Japanese saws teeth but a bit different.


Stanley saws

Re: Crosscut Saw?

#8

Re: I guess we both are Dave...

Marv....... Northern California Lake Co.

>Hi Scott,

Here's a picture of a good handle for you. Would you like me to send you the dimensions?

It's better than any of the handles on any of the Stanley saws. *grin*

Marv


img

Re: Crosscut Saw?

#9

Another one....

Marv....... Northern California Lake Co.

>Scott,

We all like choices...here's another handle, equally better than the Stanley totes.

Marv


img

Re: Crosscut Saw?

#10

Re: Wiley, Here's Stanleys page in theses saws

Wiley Horne--So. Calif.

>Thanks Scott!

I see where they say it's a three-facet tooth, so there's that in common with the typical Japanese crosscut tooth.

Little off the subject, but it is interesting that if one goes back to the earlier Lumberman's Handbook by Disston, he describes toothing styles using variable amounts of fleam, and different fleam angles front and back, all according to whether it's a hardwood saw, or a saw to be used mainly for angled cuts (miters). The Japanese smiths will still make them in those specialties. Maybe Mike Wenzloff or Marv would do the same.

Thanks again,

Wiley...wandering off subject

Re: Crosscut Saw?

#11

Awh Marv! Your a godsend!

Scott Burr in Ben Lomond, CA

>This second pic looks exactly like the handle on my Stanley 20" long 8 PPI hand saw. But, MY saw has an impressive wheat carved stamping in the handle as well.

Maybe I won't touch it. I'll leave that poorly un-centered stamped, errr... carved wheat's on the handle to remind me of you.

I feel the love tonight! 8^)

Re: Crosscut Saw?

#12

You are quite welcome, Just trying to be helpful..

Marv....... Northern California Lake Co.

>Scott,

Did you know that wheat carving your handle makes the saw cut better? :) It has to be centered though or it's like setting only half the teeth.

Marv