Are these worth anything???
RC
>I was going to throw these tools out, but first i thought i should check to see if they are worth anything.
Knowledge You Can Build On — Est. 1998
Are these worth anything???
RC
>I was going to throw these tools out, but first i thought i should check to see if they are worth anything.
Re: Are these worth anything???
ThomD
>The pliers and snips usually sell for a few bucks up to 20 if they actually work. That's twenty dollars to me, and 20 cents to some of the guys around here, you can find blacksmith tool prices on ebay. The hammer in the center, not sure what it is, if it is a shoemaking type they are sometimes worth quite a bit, 60-200, the next week one will sell for 10. If the "froe" end is sharp it isn't for shoemaking. The drawknife might clean up. The brace if it works might be of interest.
Re: Are these worth anything???
Tom MacGregor
>Those who frequent this forum are not generally known for throwing tools out. Value is subjective, and there's nothing here that's going to plump up your retirement fund. That said, if I spotted the four pieces on the lower right at a yard sale - the brace, steel(long burnisher?), ballpeen hammer & adz - I'd throw a few bucks at them. I'd also check to see if the small try square was salvagable.
Re: Are these worth anything???
Bill Houghton, Sebastopol, CA
>the only one with any likely rarity - and even that may not be true where you are - is the adze, the one in the center, kind of funny hammer looking thing with a cutting edge on one side. Not sure if that's a shoemaker's tool or a cooper's tool; one of the more knowledgeable folks might know.
The other tools are likely not much. The curved sickle-looking thing is just that, a sickle; gardening tool. I think the long round rod with the handle on it, to the right of the adze, is a kitchen-knife-sharpening steel. If it's got very subtle serrations running its length, that's what it is for sure; if not too rusty, you can use it in the kitchen - a few strokes of a knife against it will make for much better cutting.
Still, it seems a shame to toss them if you can donate them. Are you part of a church or something else that does rummage sales? Is there a Habitat for Humanity chapter near you, or a thrift store that takes tools? Someone can probably get a dollar or two for each that will support a worthy cause.
Re: Are these worth anything???
Marv....... Northern California Lake Co.
>Never throw old tools away.
They will always be worth something to someone. Over time, some tools become worth more while other tools become worth less.
Some people will modify an old tool to make it more useful for their particular purposes.
Then there are the aritistic types who can turn a pile of old tools into something artistic.
And lets not forget the restorers of tools and collectors.
So to answer your question, yes, they are worth something.
I'm a packrat. If it's metal, it stays. I rebuilt my front deck about 8 years ago. I still have the old rusty nails.
Marv
Coopers Adze
David Miller from Iowa
>The "hammer" in the center is a cooppers adze - nice tool probably worth maybe $30 - $40 on eBay.
Re: Are these worth anything???
Todd Hughes
>The thing in the center is a cooper adze and used in the wooden barrel trade and probably others. I have sold nice ones in the past for over $75. Yours looks pretty rough and the blade looks very short which affect price a lot. Cleaned up maybe a $25 tool
Have one blacksmith tong on the right that if in good condition might be worth $20
Nippers and rest of the stuff close to know vaule. The little square always a chance could be somthing but probably not. I see people put $10 on the sheep shears...bet they are glad if they sell them.
..I can't see the torch very well but kind of looks different with somthing straight up at the top. Im no expert on them but different torches can be of interest to collectors and I have sold them as high as $900 in the past. Never know but I always buy the strange ones I see and most times do well with them....Todd
Nippers and rest of the stuff close to know vaule"
Scott Burr in Ben Lomond, CA
>Does that mean you know the value?