Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Compare cordless drills on the numbers that matter

Coffin smoother wedge rebuild update

Posts

Coffin smoother wedge rebuild update

#1

Coffin smoother wedge rebuild update

Dominic in Buck's County PA

>Hi gang,

I finally got a chance to mess with that wedge I made for my old wooden coffin smoother. I used walnut for the new wedge and followed the directions I found at the Norse Woodsmith site. Side note here: That is one hell of a site! It is just chocked full of great information!

I'm glad I let this sit for a while before I went at it again. After making (2) wedges and not having either work I figured it was a good thing to leave it alone for a bit. As it stood, one of the wedges wasn't as bad as I had thought. So all it took was some careful chisel & rasp work.

It turned out that the abutments are not quite at the same angle. So I had to tweak the wedge a good deal to make it fit perfectly. Before this I used a belt sander to narrow the sides of the iron by a hair, and flattened/polished the chip breaker. But it was getting the wedge to fit right that did the trick.

Here's some shots of the smoother after trying it out on a piece of cherry.

Photobucket

Photobucket

After I was confident that I had the wedge sized correctly, I cleaned up the corners and used a rasp to steepen the incline on the inner "ramp". After all the work I did making sure they fit, I left all the sections that contacted the abutments alone!

Here's a shot after I tried the smoother on some ash.

Photobucket

The next think I'm going to do is either laminate a new sole onto this plane, or just install a insert at the mouth. Either way, I have a nice piece of pear that will work.

BTW, I was examining the front of the plane this afternoon and noticed the maker's mark. It's partially worn away but I could see a star and some letters. Anyone know of a plane maker that uses a star in their logo?

See ya around,

Dominic

Re: Coffin smoother wedge rebuild update

#2

Re: Coffin smoother wedge rebuild update

Wiley Horne--So. Calif.

>Hi Dom,

Great work! Makers who used a star:

Auburn Tool Co. (in a semi circle)

[star]

Auburn, N. Y. (straight line)

D. R. Barton (in a semicircle)

[star]

Rochester, N. Y.

{all of the above inside a half-moon cartouche}

The Birmingham

CONN

Plane Mfg Co.

[star]

W. O. Hickok

[star[

Harrisburg

{Hickok and Harrisburg arranged in a circle around the star}

J. T. Jones,

Philada

{many different logos and abbrevs. for Philadelphia--most with a star}

William Ward and also Ward & Fletcher, New York used a unique 4-pointed star

Wiley

Re: Coffin smoother wedge rebuild update

#3

Re: Coffin smoother wedge rebuild update

Peter Evans

>If a star and a crescent on the mark, then Mathieson - they made millions of planes

Re: Coffin smoother wedge rebuild update

#4

Re: Coffin smoother wedge rebuild update

Jim Shaver - Oakville, Ont

>Lovely work Dom...

Take care,

Jim

Re: Coffin smoother wedge rebuild update

#5

Re: Coffin smoother wedge rebuild update

wilbur

>Glad to see that you got it up and running! Now you'll have a whole new set of planes to start rehabbing. You might have to unload some of those cast iron models that are going to be in the way. :@)

Re: Coffin smoother wedge rebuild update

#6

Dominic in Bucks County PA

Not bloody likely!

Dominic in Bucks County PA

>Wilbur,

You wrote:

"You might have to unload some of those cast iron models that are going to be in the way.

LOL! Yeah,....like THAT'S gonna' happen! :>)

Why not keep both around? It's just that I built this big tool cabinet so that ALL my planes could live in peace and harmony. There's room enough for some of each....!

Later,

Dominic

Re: Coffin smoother wedge rebuild update

#7

I don't know Dom...

Scott Burr in Ben Lomond, CA

>I've heard they don't play well together. Iron ones want to play ON the wood ones. Not Pretty...

Nice atomic wedgie you made by the way, glad you didn't wedgie me!