Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

A55 Smoothing Plane

Homemade Marking and Cutting Gauges

Posts

Homemade Marking and Cutting Gauges

#1

Homemade Marking and Cutting Gauges

L. Hanson

>Ever have one of those moments where you realize you've been using a tool for so long that you don't actually realize just how worn out it is? I have had this old Stanley #77 marking gauge for a very long time, and I was having trouble with it. Looking at it, I realized that not only had I filed the pins to the point they were really just nubs, but also that the face of the thing had worn to where if you didn't use it at a certain angle, your line could vary by up more than 1/32". Even the brass in the face has worn...

I imagine I'll fix it back up someday. I thought about ordering a new one along with a cutting gauge I need for my current project - but then remembered a wonderful old piece of perfectly quartersawn cocobolo I had in the stash. Plus I had all this brass laying around - so off I went:

some text

some text

The two cutting gauges are based on Steve Latta's design and use Xacto #19 blades. The other three are traditionally designed - the two mortise gauges each have three pins (one underneath), with one made from 1/8" drill rod I hardened myself, and the other I used 1/16" drill bits for pin material. I even made one so the other end will hold a pencil...

The last, another cutting gauge, uses a blade I fabricated from a used-up lunchbox planer blade.

More on the gauges here if you're interested. Lots of fun to make! I should be covered for a while, now... ;-)

Leif

NorseWoodsmith.com

Re: Homemade Marking and Cutting Gauges

#2

Re: Homemade Marking and Cutting Gauges

Derek Cohen (in Perth, Australia)

>Hi Leif

Those are just wonderful.

Still, you could do with a few more in different, contrasting woods... Never have enough cutting/marking gauges, y'know .. :)

Regards from Perth

Derek

Re: Homemade Marking and Cutting Gauges

#3

Beautiful workmanship...

Marv....... Northern California Lake Co.

>Hi Leif,

Your versatility never fails to amaze me. I remember you mentioning a couple years ago that you wanted to perhaps make marking gauges and sell them. Are we seeing some prototypes here?

Very nice work on the brass as well as the wood. Probably much easier on the hands than making backsaws?

Marv

Re: Homemade Marking and Cutting Gauges

#4

Re: Homemade Marking and Cutting Gauges

Stephen Shepherd in the State of Deseret

>Leif,

Nice work, I especially like the traditional style. How many times has that third pin found a finger? I have a new made one, I think by Crown and I had to take off that lone third pin, even though the blood didn't show up much on the rosewood.

Stephen

Re: Homemade Marking and Cutting Gauges

#5

Jack Guzman from Maine

Nicely done

Jack Guzman from Maine

>Leif,

Nice job as usual. I really appreciate how you document your process and make it available so others can learn from it. I plan on using your example and updating my marking gauges.

I built a traditional(one piece)smoothing plane using the information on your website.It was simple to do following your steps.

Thanks for sharing.---Jack

Re: Homemade Marking and Cutting Gauges

#6

Re: Nicely done

C.R. Miller

>Great work Leif. Can't have too many gauges -- especially pretty rosewood ones!

Re: Homemade Marking and Cutting Gauges

#7

Gauges good yes!?!

Scott Burr in Ben Lomond, CA

>Lief, very nice work. A quick question, how do you apply, adhere the brass strips to the wood?

Thanks,

Scott

Re: Homemade Marking and Cutting Gauges

#8

Re: Gauges good yes!?!

L. Hanson

>They are 1/8" thick strips of brass (1/4" wide and 3/8" wide) set into a tight fitting dado (just tight enough they needed a little clamping or tapping to slide together) which was flooded with CA glue...

On the slicing gauges, the brass face (again, 1/8" thick, but 1" wide this time) is held in place with #4 x 5/8" brass wood screws and epoxy - though I think I could have used CA there as well, as the screws do most of the holding. The brass screws were then sanded flush.

The small handle on the sliding mortise is just a piece of brass rod held in place with epoxy. I think a better solution would have been silver solder, but I think the epoxy will last.

Leif

Re: Homemade Marking and Cutting Gauges

#9

Thanks Lief, FWIW...

Scott Burr in Ben Lomond, CA

>I've never had good luck with either glue and the same mediums.

Glad it's working for you!

Re: Homemade Marking and Cutting Gauges

#10

Re: Thanks Lief, FWIW...

L. Hanson

>I've had pretty good luck with those two glues when they are used in the proper circumstances, even though I'm not a big proponent of epoxy or CA - but in this case they work well, or at least they have in my experience. There's two things of note, however - with the face of the slicing gauges the main holding is done by the brass screws, not the epoxy, which only serves to "lock" it into place. You cannot depend on the glue alone to hold the pieces, as that is bound to fail.

With the inset brass, it's fit quite tightly into the dado, enough so that it takes some force to insert. Again, the CA glue is there simply to "lock" it into place. A good rap with a hammer will loosen them, but it has to be directed right at the insert. I know it holds well because I did just that to remove a piece I messed up while making these... It's not a force these tools will be subject to on any regular basis, though it could possibly happen if dropped, I suppose... It also could happen if the wood moves enough, but at this scale I don't think that will be an issue. But then again, you never know...

If one isn't confident the glue will hold, it's easy enough to add a couple brass pins (similarly to how Stanley did it on theirs) or even a screw or two to hold it in place, even after the fact to work in concert with the glues.

Leif

Re: Homemade Marking and Cutting Gauges

#11

Just a thought....

Marv....... Northern California Lake Co.

>I Leif,

When using Epoxy, to create an anchor so to speak, I have drilled flat bottom holes or counterbores on the inside surface of the metal. The more holes the better. The bigger the holes the better.

JB Weld is great stuff with lots of adhesive qualities and more shear strength than clear, unfilled Epoxy.

Take care,

Marv

Re: Homemade Marking and Cutting Gauges

#12

The force of shear and pull at work...

Scott Burr in Ben Lomond, CA

>What works one way doesn't necessarily work the other way. Thanks!

The glue is strong with you Lief!