Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Find a woodworking club near you

Flattening Veneers

Posts

Flattening Veneers

#1

Flattening Veneers

Sgian Dubh

>I recently added to my website a short <50 kb PDF document on flattening veneers prior to gluing them to a groundwork. Some visitors here may find the information useful.

I will probably add an image or two of particularly nastily buckled veneer to the document in the next week or two to increase the eye candy value, but the described methodolgies for flattening veneers won't change much. Slainte.

Re: Flattening Veneers

#2

Re: Flattening Veneers question....

Bob Entwisle in NJ

>Hello Richard,

Thanks for the information.

For "thin mesh plastic", would something like plastic or fiberglass window screen material be suitable?

Thanks

Bob

Re: Flattening Veneers

#3

Re: Flattening Veneers question....

Sgian Dubh

>I believe it would Bob. If I recall correctly from when I lived in the US the window screen you mention has very fine mesh with holes perhaps no more than about 1/8" or 3/16" across. The mesh is just to keep the veneer separated from the newsprint so that the two don't stick together. Slainte.

Re: Flattening Veneers

#4

Re: Flattening Veneers question....

Tony - Memphis

>That's what I use. A small roll is very inexpenisve at the local big box.

Tony

Re: Flattening Veneers

#5

A couple comments, Richard

Ellis Walentine, Host

>I have used the 1:8 glycerine:water formulation for many years, usually with a bit of liquid hide glue in there as a size. The concentrated glue solution you mention for longer-term storage is news to me, but if you say it works, I believe you. I suppose that amount of glue doesn't have any untoward effect on the final laying or finishing of the veneer.

Regarding the talk about how much bubble or blister is acceptable, I agree that it matters most if you intend to edge joint the veneers. Otherwise, you just need the veneer to press flat without breaking open any of the bubbles or ripples. But, for edge jointing, I prefer to be a bit more empirical about determining if the veneer is "flat enough." My method is to prepare two sheets of 3/4" plywood larger than the size of the veneer sheet(s) in question and to press the veneers between the plywood cauls, with just the edges to be jointed sticking out a tiny bit (less than 1/8") from the edges of the plywood sandwich. You can tell by how much pressure you need to put on the cauls -- and any cracking or popping you begin to hear as you press -- to know if jointed edges are going to be straight enough to tape for pressing or if they are going to retract everywhere the distortion is too great. That's the test. If the plywood sheets press flat with little effort, you should b okay, but even a slightly bubbled veneer may not hold a straight edge after jointing and you'll end up with holidays in the joint line.

Ellis

Re: Flattening Veneers

#6

Re: A couple comments, Richard

Sgian Dubh

>Ellis, I forgot to include a description for testing the need for flattening which I sometimes use which is similar yours, ie, the squashing the veneer between a couple of flat surfaces. I've used everything from a workbench top to a table saw and laid a piece of ply or MDF over the veeneer. Crunching noises, ripping and snapping noises, as you say, are a giveaway.

The 'concentrated' glue mixture you referred to isn't that concentrated really. It's only 2/7ths or about 28% glue. The mix, once the veneer is flat and dry, seems to hold veneers flat in most cases for quite some time. It's not a perfect cure for severely rippled veneer, but it seems to work I'd guess about 80- 85% of the time. I can't recall having problems with sticking the veneer after the treatment due to the presence of PVA glue.

You mentioned the use of hide glue instead of PVA. I've also used this, but in my case it's always been the hot hide glue. I've used about the same 2/7th proportion as the PVA mix I described. This works too, but it's often the case that this type of glue isn't handy in our workshop, so the convenience, ubiquity, and ready availability of a tube of PVA comes into play here.

Nor do I recall particular finishing problems due to the presence of the glue. I quite often use PVA glue to stick down veneer anyway, and some woods, particularly open pored ones get glue bleed through leading to localised gobs of glue showing on the top surface. In this case I usually go over the whole surface with a PVA glue wash at about a 3 glue to 7 water split, let it dry and then scrape and/or sand the surface ready for polishing. This seems to just about eliminate any tendency for isolated glue spots standing out from the surrounding wood. Of course, if there are gobs of glue here and there due to localised bleedthrough it's important to put a bit of extra effort in to remove them. Slainte.