Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Build it. Rock it. Rockler has your woodworking tools.

Is Paul Hamler still in the tool making business?

Posts

Is Paul Hamler still in the tool making business?

#1

Is Paul Hamler still in the tool making business?

Scott in Montana

>I'm seeking information on the plane scraper insert that Paul Hamler made, or is still making. I've e-mailed him at the only address I could find but have received no reply.

Does anyone know the statis of his scraper insert?

Thanks in advance,

Scott in Montana

Re: Is Paul Hamler still in the tool making business?

#2

Yes, but...

Ellis Walentine, Host

>...at the moment he's making 1/3-scale long rifles. I just had a long chat with him and he says he has about half a dozen of the scraper-plane inserts (for 2 3/8" Bedrock and L-N planes) available for sale at $150 each. You can e-mail him directly to inquire: hamlertools@alltel.net

Regarding the scraper inserts, he has an unfinished production run that should be available by the fall. After that, he says he's going to pull back from toolmaking and concentrate on some of the other things, like production miniature long rifles and such that interest him more these days.

Tell him I sent you.

Ellis Walentine, Host

Re: Is Paul Hamler still in the tool making business?

#3

Re: Is Paul Hamler still in the tool making busine

Wiley Horne--So. Calif.

>Hi Scott,

I received an early prototype of Paul's scraper insert within the past year, several months ago, and at that time he was close to finishing a production run. BTW, the scraper works really well--he recommends putting it into the shoe of a No. 6, which is what I did.

I heard from Paul about Christmas from the following email:

hamlertools@alltel.net

He told me last summer that after the scraper inserts, he was going to start his prototype to reproduce Davy Crockett's Pennsylvania-Kentucky rifle--a collector he knew owned the original and was cooperating.

Wiley

Re: Is Paul Hamler still in the tool making business?

#4

What does one do with a 1/3 scale long rifle?

Greg B�tit, Crown Point, NY.

>I'm just trying to figure out what the market is for such a thing. Dolls (Ol' Betsy for Betsy McCall)? Black powder shooting competition for little kids?

greg

Re: Is Paul Hamler still in the tool making business?

#5

Shoot small game, of course

Bill Houghton, Sebastopol, CA

>

Re: Is Paul Hamler still in the tool making business?

#6

LOL (for real!)!!

Paul Kierstead

>

Re: Is Paul Hamler still in the tool making business?

#7

Re: What does one do with a 1/3 scale long rifle?

ThomD

>It is comparable to making miniature furniture, there are some people who just love the idea of something intricate being reduced in scale and therefore even more intricate. Doesn't presuppose use by elves. As long as the work can be done to a decent standard - it can be difficult to get something like the wood grain right since they don't sell 1/3rd size wood grain. Small size screws can be managed but it is very fine work.

For the maker there is the thrill of being able to take on more of the job if it is smaller in size. Obvious with model railways, but it could even be the case here, though I may be wrong. I would really like to make a barrel drilling and rifling machine, and it is practical to a certain degree. While making a small barrel would be more difficult, it would be on a smaller scale, less tedious and smaller home scale shop tools. On a full size rifle the octagonal contours on a rifle barrel would require a mill large enough to take the largest barrel, plus any extra length required to set it up. That's an industrial machine like a Bridgeport with a long table. Cut that down to a third and a lot of small machines would get the job done in a home shop.

Some of the small guns can be used like the ubiquitous gattling guns that shoot 22lr, rather than the 45-70. Scaling down loads would be challenging since the powder would need to be scaled down also, and that is a whole other issue, still there is always a way.

Re: Is Paul Hamler still in the tool making business?

#8

Paul built his own rifling machine

Ellis Walentine, Host

>He converted a small machine lathe to a CNC variable-pitch rifling mill. He and another buddy of mine made a full-size version last year.

Ellis

Re: Is Paul Hamler still in the tool making business?

#9

Re: Paul built his own rifling machine

ThomD

>Well you aren't going to get a long spiel from me about that, because that is way above my pay grade. The one I wanted to make has a mechanical interface to adjust the pitch. The scary part to me is the 700 psi oil. The other scary bit is that it seems like one would need to spend a lot on reamers. The rifling cutters one can make,but the other cutters are real expensive. With my luck I would just get set up, and the US would restict export of reamers, as they do with a variety of other firearms parts. It sorta appeals to me as nearly the ultimate in a basement do it yourself thing.

Re: Is Paul Hamler still in the tool making business?

#10

Re: Paul built his own rifling machine

Pam Niedermayer, Austin, TX

>Yeah, well we want to export the finished goods, not the parts. :)

Pam