Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

This $39 jig will make you a WOODWORKING GOD!

Workbench: Step 1

Posts

Workbench: Step 1

#1

Workbench: Step 1

Mark in Texas

>I recently came home from a local woodworking store (sadly going out of business, but that's another story) with a 8'x30"x2.25" segment of maple bowling alley, heavily varnished on one side.

The slabs are nailed, so they have to be taken apart and glued. The regluing will be facilitated by the existing tongue and groove. After that, I'll clean up either the top or bottom with planes after glue-up.

As you might expect, I'm planning to make a new workbench. I haven't selected a plan yet; I'm currently reading Scott Landis book. I've also followed recent posts here. I welcome suggestions, especially of the type "don't make a serious mistake by doing ...."

Mark


img

Re: Workbench: Step 1

#2

Re: Workbench: Step 1

Mark in Texas

>Obviously, I couldn't figure out how to post the stupid image.

Re: Workbench: Step 1

#3

You might consider Chris Schwarz' book too

Bill Houghton, Sebastopol, CA

>I bought that recently and, having read through it once, found his analytical approach to workholding very helpful in thinking about bench design.

Re: Workbench: Step 1

#4

Re: Workbench: Step 1

steve mackay

>Never used it but you got lucky with that score ! Everytime I see a bowling joint going out or re-furbing I go in and ask about getting some and a contractor has always already bought the alleys whole-lot. From what they say they get crazy prices for it.

Re: Workbench: Step 1

#5

Re: Workbench: Step 1

ThomD

>Benches are pretty simple, essentially a slab of wood on two horses, with a few things tacked on. These are my list of things to be on the lookout for:

- Fit of parts together.

It is so easy to do something like build the dog holes only to find there is a great big hole going to be wherever you place the vice because when you set the ideal spacing it is subsequently inevitable that it fouls your vice

Of you make the base first, and it turns out the top when made actually ends up a little narrow, because you had to remove more material than you thought you did to get the parts squared up for glue-up, etc...

The major rule here is to build it backwards. Start with the vises first, then the top, build the base last. This is a classic project issue. People want to spread out the cost and buy the expensive parts last, when success seems clear. So they build a motorcycle frame and when that turns out they then go out and buy the motor... Oops! Of course one can start with a plan, source only identical parts and build to spec, but that isn't always necessary or smart any more than it is to cut all parts of your cabinet to perfect specs and bring them together, the normal approach being to fit parts together.

- Height of Bench. There really is no way of winning here. There are certainly some rules of thumb, but you both have to feel your way to your own body, and fit to your own work. In that regard if you look at the Landis book, which is still the best ATMO, It was written at a certain point when stuff like routers were a bigger part of the average small shop, and the hand tool environment had a different character than now. For instance the average plane was probably a little lower. An adjustable height bench makes sense really, and I probably wouldn't build another bench without it. I have this hydraulic lifting cart I use for moving machinery and just having it in the shop has totally convinced me, even though I love a trestle base.

- Fit of bench to work environment. This is also a toughie, again hard for a beginner (which is what all amateurs like us are) to get this right. We are a mobile society so we probably change shop spaces a few times, buy different tools, and learn different techniques, but one should put a lot of though into how one works, the kind of work one does, the shop size and layout.

Re: Workbench: Step 1

#6

Re: Workbench: Step 1

Craig in AK

>Hi Mark,

I've been working with some bowling alley for a couple different projects and can't say it's much fun. Pulling the boards apart is the hard part. I didn't have any luck pulling the nails out and there are a lot of nails. I tried prying the boards apart and a lot of them split. What I ended up doing was using a hole saw to drill around the nails and seperating the boards that way. I burned up a couple hole saws but it's the best way I've found so far. Let me know if you find any easier ways.

Craig

Re: Workbench: Step 1

#7

Re: Workbench: Step 1

Derek Cohen (in Perth, Australia)

>Mark

I apologise if I am the messenger of bad news. This question has come up before and, although I have never handled a piece of bowling alley, I recall that all eventually tossed it away in frustration owing to the impossible task of removing the multitude of nails that it used for construction. I suspect that you are going to find better use for it as the lower part of a dual laminated worktop.

Regards from Perth

Derek

Re: Workbench: Step 1

#8

Re: Workbench: Step 1

Mark in Texas

>I'll give it the old college try anyway. I've only got $40 invested in it, so I'm not out much if it fails. I typically waste that amount of money on a visit to the adult beverage store.

Mark

Re: Workbench: Step 1

#9

Re: Workbench: Step 1

charlie belden

>Might want to rething things - they used "square" nails - every 6 or eight inches - through the groove of the tongue and groove

- just like in hardwood flooring - the real stuff, not the glue down stuff. And, because that maple is harder than oak flooring, which is why they use maple for bowling alleys, those nails tend to be "difficult" to remove - even if you're willing to destroy the groove - or the bottom half of it.

Free - or cheap - often isn't - if you include your time and the blood you're likely to lose "prepping" - or dealing with a spouse who is offended by cursing and swearing - or angry tool hurling.

Look into finding some old chemistry lab tables. They're usually 1 1/4 to 1 3/4" thick and take less effort to clean up. Oh - and they're typically hard maple.