Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

If you sell to woodworkers, your customers are already here

Thick Maple Bench top

Posts

Thick Maple Bench top

#1

Thick Maple Bench top

Jeff Johnson

>I'd like to make a bench with a 3" thick top, but don't want to go through the extreme hassle of glueing up myself. (would rather make furniture than a slab). The thickest I can find commercially is 2-1/4". Any suggestions?

Re: Thick Maple Bench top

#2

Re: Thick Maple Bench top *LINK*

Hank Knight

>Bally Block makes a 3" thick laminated maple food prep top. They don't sell direct; you have to go through a dealer. I ordered a 3" X 24" X 72" top from their distributor here and built my bench top around it (I glued on dog hole strips and end caps). It was an expensive start-up cost, but I'm glad I didn't have to mess with gluing up the whole top, and I'm real happy with the end result. Actually, if you do the cost analysis, you'll find it's not outrageously more expensive than buying 8/4 maple and building your own. I ordered mine unfinished with square edges so it was easy to add the dog hole strips. Heres a link:


Bally Block Maple Tops

Re: Thick Maple Bench top

#3

Re: Thick Maple Bench top *LINK*

Alan DuBoff

>Jeff,

Are you looking at the Bally's or similar? I know I was looking at those when I put one together, and there was some local to me that a dealer was trying to close out, but their price wasn't much lower.

FWIW, I think 2 1/4" will make a pretty good bench.

This page at the link says they will construct a custom top for you, why not contact them?

In the end it gets down to time and money...unless you stumble into something...I have a 1 3/4" slap I acquired on some flimsy metal legs, I'm going to build some better legs for it eventually. The top is plenty thick enough for a bench top, not as sturdy as my 2 3/4" top, but still, it will make a great bench with a solid set of maple legs.


Michigan Maple Block / Bally

Re: Thick Maple Bench top

#4

Hire a local shop to make it

Bill Tindall, E.TN

>It is a trivial job for a shop that has a planer or wide belt sander. Should you have such a shop near by see what they will make it for. Tell them what you are willing to accept in terms of appearance defects, etc. as this discussion could lower lumber cost. Should you find a shop that works much maple they might have lumber with dark heart wood that they can't use for cabinets, etc.

Re: Thick Maple Bench top

#5

PS

Bill Tindall, E.TN

>Should you hire someone to make it consider making it from ash. Ash is but slightly porous, doesn't splinter and it is cheap. I think it would make a fine bench.

Re: Thick Maple Bench top

#6

Re: Thick Maple Bench top

David Cockey

>I'm using one of the 3" food prep tops in my bench, currently under construction. Purchased it from LL Johnson in Charlotte, Michigan. The top will require flattening, and there are a couple of cracks in on end. But if I hadn't started with the top completion of the bench would be further off.

Re: Thick Maple Bench top

#7

Re: PS

Edward in Vancouver

>Options:

Check out used food eqpt. stores/bakery suply places for maple top prep tables. These are usually 13/4 thick and may require some flattening. Sweden (a.k.a Ikea) has 1/1/2" thick beech, oak and birch counter tops that might do the trick as well.

Re: Thick Maple Bench top

#8

Re: PS

Jeff Johnson

>Thanks for the responses, guys. You've given me some great sources, and a few things to consider.

Re: Thick Maple Bench top

#9

Re: Thick Maple Bench top

ThomD

>There isn't any advantage to a randomly glued up top like that. There are potential disadvantages:

- The wood is possibly lower grade

- The wood is not oriented for planeability, so if you need to surface it by hand later it may tear up on you since they did it all in an abrassive planer, not with an edged planer. Even a rotary plane cust with less tear if se up for it.

- Stability issues. A lamination of this orientation yields no significant stability advantages from it's lamed wood geometry, but it incorporates all kind of mismatched pieces of wood from different trees, so good luck with that. In use it is intended to be perimeter fastened to a steel base.

- Looks, well I won't go there, except to see I don't think I would pay extra for it.

As against that is the fact that you can make many benches out of monolithic pieces. Or two pieces. By the time the dog holes are applied you are probably looking at no more work to prep a single piece than to prep a few boards, except that you will have to plane the bench piece if you so choose.

Where there is a big time savings is if one were planing on making a laminated top like one of these on one's own. That is labour intensive, and gluey, and one needs clamps. Just saying that most bench styles were designed around single pieces anyway, what with the tool wells, so there are other options if one so chooses.

Re: Thick Maple Bench top

#10

Re: Thick Maple Bench top

Hank Knight

>Thom,

The only point I agree with you on is the planeability point. The commercial laminated top I got from Bally was not fabricated with hand planing in mind. I had some tear-out when I flattened and surfaced my top with hand planes, but it wasn't bad and I was able to cure most of it with a good smoother with a sharp blade and a scraper. I've not had any of the instability issues you describe and I have no complaints about the quality of the material Bally used. My top is supported on two rails, not by a perimeter frame. For me the commercial lamination saved me a lot of work. My shop is small and the thought of wrestling a heavy, multi-step top glue-up around in it was something of a nightmare. The Bally top saved me all of that. I'd do it again in a heartbeat.

Hank

Re: Thick Maple Bench top

#11

Re: Thick Maple Bench top

ThomD

>Just to be clear I did not say there would be instability problems, I said:

a) the form of lamination does not contribute to stability, as it would if if were made up of, say, 1/16" 0 oriented veneers. Lamination could be used to improve the stability of bench tops, but I can't remember ever having seen this done in any of the many books or articles on the subject.

b) I also pointed out that the use of multiple pieces of wood is not helpful to stability in this case. The fact your pieces didn't plane shows the random risk involved that one piece of wood with a bad tendency will be in the top.

I also didn't say this piece would have to be secured on all sides, I am just describing the design use. If one applies the component to another situation it is well to understand the design use.

My over all point is something like this: If I want a chicken, I buy a chicken. The discusion of laminated tops is like listening in on people who need a chicken and are discussing the various options in chicken meat product. Is a luncheon meat with thicker slices less work to reconstitute a chicken out of, or should they buy canned chicken meat or burgers, etc... Maybe mechanically deboned chicken in a drywall gun and sprayed over a wire frame?

They make full sized pieces of wood suitable for bench tops, ranging from trees, rough sawn, reclaimed, etc... Price ranges from free, to very expensive. I am merely pointing out that laminated parts are not necesarily less labour or cheaper. There is no need to glue anything up. Traditional bench design is scaled off full size piecs.

If a person particularly wants to work on a wide table top, some folks prefer 48" wide tables, then the situation changes. But the tops on many benches are narrow and do not need to be glued up at all. Just an alternative.

The issue of wood quality is mostly related to price. These laminated tops are made of lower cost pieces, lots of little pieces. This is the usual strategy of making larger parts out of small pieces, nothing wrong with that, but it isn't worth paying the high processing cost if the material does not fit the use. The ideal piece would be absolutely straight grain wood, that plained like butter from either end. I would pay for that.

Re: Thick Maple Bench top

#12

O.K.

Hank Knight

>