Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Nearly 100 Exotic Wood Species, Direct-Imported Since 1972. Shop Slabs & Turning Stock.

Refurbed Bdrock 605 1/2 & 606

Posts

Refurbed Bdrock 605 1/2 & 606

#1

Refurbed Bdrock 605 1/2 & 606

Dominic in Buck's County PA

>Hi gang,

Here are some before and after shots of (2) Bedrock planes I refurbed this weekend.

One is an early "round sided" Bedrock 605 1/2 and the other is a Bedrock 606. As you can see, both were in somewhat rusty condition when I got them.

Bedrock 605 1/2: BEFORE

Photobucket

Photobucket

Bedrock 606: BEFORE

Photobucket

Photobucket

I soaked them in Evaporust for 24 hours. This is the first time I used that stuff and I have to say that it did make the clean up job easier. I still needed to hit a couple pieces with a brass wheel brush. But that was only because they were REALLY rusty. I will definitely use it again.

Evaporust bath:

Photobucket

After they were removed from the Evaporust, I washed them off with some mineral spirits. After they dried I buffed all the parts with a medium brass wire wheel brush. After that I gave all the parts a coat of 3-in-1 oil and allowed them to sit overnight. The next day (today) I ground a new bevel, flattened the back of the blade, and honed them. I also worked on the chip breakers. These were in Ok condition but needed to have the mating surfaces ground flat and the tops sanded smooth and buffed.

One side note here: Someone suggested wiping down your stropping surface with mineral oil to help green honing compound adhere. Well, that worked GREAT and I have the cut up fingers to prove it! Man these blades are SHARP!

I tested them both out by squaring up a Cherry 4x4. While I like the way the 605 1/2 performed, I was most impressed with the 606. The mass of this fore plane really makes powering through tough job a breeze.

Bedrock 605 1/2: AFTER

Photobucket

Photobucket

Photobucket

Bedrock 606: AFTER

Photobucket

Photobucket

Photobucket

Thanks for viewing!

See ya around,

Dominic

Re: Refurbed Bdrock 605 1/2 & 606

#2

Very Nice!

Greg B�tit, Crown Point, NY.

>

Re: Refurbed Bdrock 605 1/2 & 606

#3

Nice job Dom.

Victor Parisian

>Are you sure you didn't photo-shop those pictures? They sure look nice and clean and bright in the after pics.

Victor - in Houston

Re: Refurbed Bdrock 605 1/2 & 606

#4

Re: Refurbed Bdrock 605 1/2 & 606

Wiley Horne--So. Calif.

>Wow. That is really a classy job of making those Bedrocks look right. Not overdone or too high a shine; just right.

Very nice vintage planes too!

Wiley

Re: Refurbed Bdrock 605 1/2 & 606

#5

Refurbished Bedrocks

Philip Duffy

>Dom, Very well done! Looks great. You have a special talent with this process of yours and the results show. Thanks, phil

Re: Refurbed Bdrock 605 1/2 & 606

#6

I'm envious

Ellis Walentine, Host

>I've been wanting a 606 for a long time. What flea markets have you been prowling anyhow? :-) Those are beautiful specimens.

Nice job.

Ellis

Re: Refurbed Bdrock 605 1/2 & 606

#7

Re: Refurbed Bdrock 605 1/2 & 606

Bob Demers

>Wow, that evaporust really works well, I like the results.

I must try that. I dabble with electrolysis, but always had trouble with flashover rust afterward, could never get to it fast enough.

That method does not seem to have that problematic?

It also does'nt seem to leave a tell tale coloration like some chemical products.

Must pick up a bottle on my next LV visit. They can't ship the stuff, and I can't bring it back on a plane, it may be a while though..

Bob

Re: Refurbed Bdrock 605 1/2 & 606

#8

Re: Refurbed Bdrock 605 1/2 & 606

wilbur

>Really nice job, as always, Dominic!

How much Evaporust did you need to fill that tub?

Re: Refurbed Bdrock 605 1/2 & 606

#9

Dominic in Bucks County PA

(2) bottles of evaporust

Dominic in Bucks County PA

>Wilbur,

Thanks for the compliments! I used (2) bottles of Evaporust to fill that tub. The directions say you should totally immerse the object. So I did.

See ya around,

Dominic

Re: Refurbed Bdrock 605 1/2 & 606

#10

Dominic in Bucks County PA

Re: Refurbed Bdrock 605 1/2 & 606

Dominic in Bucks County PA

>Bob,

Thanks for the compliments!

You wrote:

"That method does not seem to have that problematic?...

It also does'nt seem to leave a tell tale coloration like some chemical products."

Evaporust DOES leave the surface a bit "gray". But it buffed out quite easily. Also, you need to wash the items off thoroughly after you remmove them to get rid of the "slime" left from the de-rusting process. The big thing is to coat them with 3-in-1 oil after you wire brush them. This really helps to eliminate any "instant rusting" you would see.

BTW, I got my Eavporust from the local Harbor Freigh Store. Check and see if there is one in your neighborhood.

See ya around,

Dominic

Re: Refurbed Bdrock 605 1/2 & 606

#11

Dominic in Bucks County PA

Re: I'm envious

Dominic in Bucks County PA

>Ellis,

Thanks for the compliments!

I actually scored this bad boy on Ebay (of all places)! I just kept my eye out for a later model 606 and I just happened to snag this one for $78 (yeah, I know...I suck). If you think that's bad wait till you see my next refurb. It's a 608 that I got for $82 off of Ebay! :>)

See ya around,

Dominic

Re: Refurbed Bdrock 605 1/2 & 606

#13

Dominic in Bucks County PA

Re: Refurbed Bdrock 605 1/2 & 606

Dominic in Bucks County PA

>Wiley,

Thanks for the compliments!

I intentially stopped short of shining them up too much. I just wanted to remove the rust and get the sole as clean as possible. maybe it's just me, but I found that the cleaner it is, the better it seems to slide across the wood (with some wax to help it along). Since they were in great shape already, I left the tote and knobs alone. They still have some paint splatter on them. But I don't care. They feel great!

See ya around,

Dominic

Re: Refurbed Bdrock 605 1/2 & 606

#16

Re: (2) bottles of evaporust

Chicago Bob

>I'm sure that you are aware that you can filter the used evaporust (2 coffee filters in a funnel works OK)and reuse. When it no longer removes rust in a timely manner, you can reconstitue the stuff by adding citric acid, which makes using evaporust much lower cost over the long run. The only problem I have experienced using evaporust is some planes flash rusting immediately after the water rinse but before I could apply oil to the surface.

Citric acid USP powder is available on ebay at a low cost and the amount to add can be found by searching "rust removal" and "citric acid" using google search engine.

Hope this helps lower your costs. Not much feels better than restoring an old rusty plane and hear the "swoosh" as you plane newspaper thin shavings.

Bob Haines

Re: Refurbed Bdrock 605 1/2 & 606

#17

Re: (2) bottles of evaporust

wilbur

>If you can use citric acid to replenish Evaporust, could you just start with citric acid and water and make your own?

Re: Refurbed Bdrock 605 1/2 & 606

#18

The Rock's 605 1/2 & 606...Oh Yea!

Scott Burr in Ben Lomond, CA

>Dom, A sweet job on those planes. Thanks for the tips on cleaning 'em up!