Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Exotic Hardwood, Personally Sourced Worldwide. Inspected at Origin. Shop Rare Stock.

Not quite fine woodwork, but fine wood.

Posts

Not quite fine woodwork, but fine wood.

#1

Not quite fine woodwork, but fine wood.

Derek Cohen (in Perth, Australia)

>Jarrah flooring in the office I am building above the workshop/garage at home. All tongue and grooved and 19mm thick. Took an entire weekend to do with the help of a friend.



That shot is looking through from the waiting room, past the entrance on the left, to my consulting room. The end window frames the top of a Jacaranda.

Skirting still to go on.



Below is a part of the waiting room - this room could be converted into a kitchen, hence the pipes sticking out the floor and wall.



I needed a way to hide these, so I built a bookcase. This will house magazines and children's books. Jarrah top and Pine carcase.



It's a sort-of-Shaker-Derek design.



Regards from Perth

Derek

Re: Not quite fine woodwork, but fine wood.

#2

Re: Not quite fine woodwork, but fine wood.

Hank Knight

>That's really nice looking, Derek. It should last a long time.

BTW, I envy your balmy weather (open windows, green leaves, etc.). It's really cold here.

Hank

Re: Not quite fine woodwork, but fine wood.

#3

Re: Not quite fine woodwork, but fine wood.

ThomD

>Is that one of those deals where you dovetailed the top, and biscuit jointed the bottom. I've done that, felt dirty, but... Or did you do a sliding dovetail? I once did a bookcase like that where I took the high road and put the tails on the top to brace the loads of the shelves, but I biscuited the framing shelf. Actually, all five shelves were biscuited, so pretty much zero chance of it coming apart. Supprised I got it together!

Re: Not quite fine woodwork, but fine wood.

#4

Re: Not quite fine woodwork, but fine wood.

Alex Grigoriev

>1. I see you didn't feel like getting rid of roller marks on your pine boards :)

2. I wonder if I make pins on the sides, and half-blind tails on the top, would it make more sense? Can half-blind DT be made that way?

Re: Not quite fine woodwork, but fine wood.

#5

Re: Not quite fine woodwork, but fine wood.

Derek Cohen (in Perth, Australia)

>Hi Thom

No biscuits. The lower shelf is inserted into a dado, glued and toe-nailed (from the underside). The centre shelf is adjustable over two heights (the rests are set into mortices so that they cannot move).



Regards from Perth

Derek

Re: Not quite fine woodwork, but fine wood.

#6

design

paul womack

>Nice floorboards!


Whilst I admire the skill in cutting those DT joints, I find such a small number of very narrow pins dis-proportionate; I'd have preferred a more Arts and Crafts approach. The whole "evident integrity" thing.

I have no doubt, since the load on the joint is rather low, that your joints will be strong enough though.

BugBear

Re: Not quite fine woodwork, but fine wood.

#7

Re: design

Derek Cohen (in Perth, Australia)

>Hi BB

The other furnishings are a little too modern for Arts and Craft. Ash and a soft tan wool upholstry.

The choice of dovetails started off an attempt to make the piece look "light", that is, create a sense of delicacy. I must say that I think this works and it does look better in the flesh. Chopping into this Jarrah was really hard work.

The construction is very strong - a little overengineered if anything, as I have visions of hyperactive young children climbing on everything - and there is strength also due to the glue.

Regards from Perth

Derek

Re: Not quite fine woodwork, but fine wood.

#8

What no WC?

Scott Burr in Ben Lomond, CA

>No not wood central...

Derek, looks fantastic. Seeing what I pay for a piece of jungle wood like that. Guess the economic times haven't hit ya.

Noe why would you put such a great piece of wood on a POS pine frame!?!

Re: Not quite fine woodwork, but fine wood.

#10

SWEET!

Scott Burr in Ben Lomond, CA

>