Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Veritas - Innovation in Tools

Shop Reconfig

Posts

Shop Reconfig

#1

Shop Reconfig

Dominic in Buck's County PA

>Hi everyone,

Ever get one of those projects that spawned several dozen? :>) Well that's what happened to me when I was working on my hand tool cabinet.

I needed to hang it on a wall, so I had to clear some space. In order to do that I needed to move some tools around. And from there, well it escalated into a full shop reconfiguration.

I started with re-studding out the back wall (where there was an opening for an old garage door), running some lines for outlets . While I was doing that I water proofed, added insulation, hung 3/8" T&G plywood wainscoting, 1/4" white pegboard, and a chair rail. After that I moved the bench closer to the door, and moved my lathe closer to my dust collector. I also re-vamped my DC piping and added a floor sweep, and a dedicated run for my bandsaw, lathe, and tablesaw.

Aside from moving my axillary bench to the front and moving some tools around in the front portion of the shop, I really concentrated on the back portion of the shop. But it seems that this is the section that gets the most action whenever there is a project,

Here's are some old photos that give you an idea of the way it USED to look:

Old Shop configuration

Old Shop configuration

And here is the way it looks today.

New Shop Layout

New Shop Layout

I am VERY happy with the new layout. It's a lot easier to work at my bench. All the power tools are easier to get to and work on. Plus the insulation, wainscoting and pegboard make it MUCH quieter and warmer to work in.

See ya around,

Dominic

Re: Shop Reconfig

#2

Nice job, Dom!

Stuart Hough

>I too have decided that this is the year to really do my gara...er...shop the justice it deserves. Insulation, lighting, adding 220v frthe bigger tools, T-111 siding on top of the insulation, and a ceiling, so I can control the temperature better and get the added bonus of the reflected light. I figure it will cost me about $2000 to do it, but the resulting atmosphere and organization will turn it into a great place to unleash the creative animal! Thanx for the pics!

Re: Shop Reconfig

#3

Hmmmm,Still looks like a...

Scott Burr in Ben Lomond, CA

>Rat hole!

Just kidding Dom, looks like you have a lot more room now. This is something I need to do as well... Well one of these days.

Re: Shop Reconfig

#4

Warning...

Marv....... Northern California Lake Co.

>Hi Dom,

Been there, did that....

In case you haven't noticed, just wanted to warn you about a turned bowl thats on a shelf just above your lathe. It's setting right on the edge and is about to fall. You need to rearrange that shelf so you can move that bowl back about two inches. (grin)

Marv

PS...didja give any thought to entering your shop in the shop contest? I was going to enter mine, but that would mean I'd have to clean it up.

Re: Shop Reconfig

#5

Re: Shop Reconfig

Jim Shaver - Oakville, Ont

>So where do you hide your collection of clamps??

Nicely done buddy!!

Take care,

Jim

Re: Shop Reconfig

#6

Dominic in Bucks County PA

Hi Jim

Dominic in Bucks County PA

>Jim,

My bar clamps are along the far wall in back of the dust collector (not pictured). My spring clamps are hanging from a 3/4" dowel suspended from the rafters. The rest are hanging from a pegboard in the front of the shop.

later,

Dominic

Re: Shop Reconfig

#7

Paul Kramer

Re: Shop Reconfig

Paul Kramer

>Dominic,

I see you added that center support to your hand tool cabinet. Did that get it? Sagging issues resolved?

Paul

Re: Shop Reconfig

#8

Dominic in Bucks County PA

Center Support

Dominic in Bucks County PA

>Paul,

Yup, that did it! I propped the center up and added that gusset soon after I saw the lower shelf sagging. I also ended up re-hanging the cabinet about 3" lower so I could get to the top shelf easier.

When I designed the cabinet I intended that all the plane cubbie dividers be hardwood that was attached via glue and brads to the upper and lower shelves. However in a fit of utter stupidity I decided that using 1/4" hardboard would be better.

Needless to say, those joints failed in tension soon after I loaded all my planes into the cabinet. THAT'LL teach me to change the design in the middle of the project!! :>)

See ya around,

Dominic

Re: Shop Reconfig

#9

Re: Shop Reconfig

Thomas Skaggs, Foothills of Mount Level

>Judging from the stool I see in the top picture if you ever tell me that you have your "you-know-whats" in a vise then I'll believe you! ;-)

Tom

Re: Shop Reconfig

#10

Dominic in Bucks County PA

Re: Warning...

Dominic in Bucks County PA

>Marv,

You wrote:

In case you haven't noticed, just wanted to warn you about a turned bowl thats on a shelf just above your lathe. It's setting right on the edge and is about to fall. You need to rearrange that shelf so you can move that bowl back about two inches.

Actually, I'm teaching that bowl to balance that way. STAY bowl! STAY! GOOD bowl!

It's not really that bad. The photo makes it look worse than it really is. It sits on the shelf rather solidly.

Re: Shop Reconfig

#11

Dunno if'n I missed it, but...

Scott in Douglassville, PA

>...is there a picture somewheres of the inside of the cabinet? Curious minds, ya know... ;-)

Scott

Re: Shop Reconfig

#13

ROTFLMAO!

Scott Burr in Ben Lomond, CA

>Nice Tommy.

Man o man I love pottie humor!

Re: Shop Reconfig

#14

SHHH! Don't encourage him!!

Dominic in Buck's County PA

>Or we'll never hear the end of it! :>)

Rock on Tommy! Shine on you crazy diamond!

Dominic

Re: Shop Reconfig

#15

Alvin!!

Scott Burr in Ben Lomond, CA

>Get away from the twin screw, no Alvin, nooooooooooo!

OK Dom, Shhhh be very quiet, we're hunting...

Tommy's!