Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

If you sell to woodworkers, your customers are already here

Dying Wood White

Posts

Dying Wood White

#1

Dying Wood White

Tom Colligan

>Just for making stringing from a veneer, that is.

Rob Millard has some tremendous DVDs on making Federal Period Furniture. When banding or inlaying, ebony proves too brittle to work with so a substitute wood is dyed black. That's easy enough and there are a number of ways of doing this.

But has anyone heard of a way of simulating holly, a common wood for stringing? It's not too available and quite expensive so is there a way to dye a veneer piece white? TIA, Tom.

Re: Dying Wood White

#2

bleach *LINK*

tek,brunswick

>This two part wood bleach works well. I would start with a light colored wood to begin with. Some maple is pretty light. The bleach doesn't penetrate all the way through. You don't want to cut the wood surface down much or the original color will show.


Klean strip wood bleach

Re: Dying Wood White

#3

Re: Dying Wood White

ThomD

>Poplar is a good base wood for that kind of thing. One of the more famous classical guitar makers used to dye poplar to substitute for other woods he used pressure cookers to get full penetration. One of the reasons he did it was because ebony, etc... would transfer a lot of energy to the instrument if a dent did occur, and of course a musician would try to avoid such wacks, but better they ended up with a piece of dented purfling, than a split in the tonewood.

With something like federal furniture, if you are doing real repros, there is far too much money and time in them to use anything but the best materials. I think it will end up looking cheap, will not be refinishable, etc... This is a case where the real look is everything.

Re: Dying Wood White

#4

Re: Dying Wood White - How about Holly???

John Aniano still reading Moxon in NJ...

>Tom,

Try to find some American Holly for your inlay- you don't have to dye it - a near porcelain white naturally without bleaching.

My $0.02,

John

Re: Dying Wood White

#5

Sycamore

Stephen Shepherd in the State of Deseret

>

Re: Dying Wood White

#6

English Sycamore

Victor Parisian

>Beautiful white and affordable. Works like maple.

Victor

Re: Dying Wood White

#7

Re: English Sycamore

Warren in Lancaster, PA

>English "sycamore" is a maple. Acer pseudoplatanus.

Re: Dying Wood White

#8

Listen to Thom and John

Wiley Horne--So. Calif.

>Hi Tom and all,

Here's a hard-earned lesson (several times over): If one is new to something, do it the way it is always done until experience is gained. What I have learned the hard way is that things are done as they are for a reason, and this is true for the details and ornament as well as the main joins, Usually more than one reason.

Specific example: You might do OK with soft maple, bleached. But my experience with thin strings of soft maple is that it got like mush, and quickly, when driven into the hot glue; also was prone to breaking if not handled very carefully. Because the wet strings did not have much strength, I really only had one shot, and if the fit was a little off, pulling it out and rehandling it was very high risk. I will admit in that project I was not using a thicknesser--which is a must by the way--and sometimes my micrometer checking overlooked a fat place which balked on me at a critical moment. Also my strings were slightly under 1/16"--if you're using heavier strings the strength issue might not be there.

The reason I was using the soft maple was that I had some really white-looking pieces on hand for drawer sides and the like. Soft maple will tend to be whiter than hard maple (IME). But. Once the strings were installed, I noticed that there were fine streaks of color surfacing here and there. I didn't notice those flecks before the strings were installed and the glue and finish hit them. The strings did not finish out nearly as clean as I expected.

I shoulda used holly. It is stronger, finer grained, and a cleaner white. If your overall methods are better than mine, you might get soft maple to work. But I suspect the bleaching will weaken it, and I wonder if the bleach treatment will last, and also if it will finish out as clear as you hope. Small color variations jump out more at you in a thin string than they do in a larger board.

I think if I were going to bleach something, it would be hard maple, hoping that at least it will handle well, and hoping that I could get the yellow out of it. But. With holly you don't have to hope.

Just my 2 cents Tom. I know this sounds preachy, but I just want to convey one of my (many) screwups, so you and others can be guided by it.

Wiley

Re: Dying Wood White

#9

Thanks to all.

Tom Colligan

>

Re: Dying Wood White

#10

Tom....

Marv....... Northern California Lake Co.

>Hi Tom,

Howz that wheat carving coming along?

Marv