Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Good Hope Hardwoods - Walnut Slabs & Specialty Hardwood Lumber

Japanese plane ID

Posts

Japanese plane ID

#1

Japanese plane ID

Bob Demers

>Pam et al

Your list of bed angles from 33 to 52 degrees got me thinking about my one and only Japanese plane.

I never knew that they were so many different, bed angle optimized for so many woods. Very cool. Thank you.

Can you help me ID my plane as to its maker by the logo on its iron?

Dont really care about its value, but im interested in its history.

I picked it up in a asian antiquites places near Digby NS

Anything you can tell me about it would be appreciated

Thanks


img

Re: Japanese plane ID

#2

Side view 

Bob Demers

>


img

Re: Japanese plane ID

#3

Top view 

Bob Demers

>


img

Re: Japanese plane ID

#4

Re: Japanese plane ID *LINK*

Pam Niedermayer, Austin, TX

>Sorry, but I can't read ideograms, so not much help on an ID. You might get a better answer if you post the question in a Japanese woodworking forum. Do you plan to tune it up and try to use it?

Also, a note on those bedding angles: usually you'll be OK if you're within 3-5� of the tentative ideal.

Pam


Japanese hand tools forum

Re: Japanese plane ID

#5

Re: Japanese plane ID

Bob Demers

>Yes Pam, I certainly plan on using it again..

I did sharpen the blade and got fluffy shavings out of it, years ago but unfortunately in between moves the wood dai has swollen and made the blade difficult to remove.

Before I start tweaking the dai, i want to know more about it.

every other tools I own I have documented to a large extend, but on this one I draw a blank

Thanks for your suggestion, i'll certainly give that a try

Bob

Re: Japanese plane ID

#6

Re: Japanese plane ID

Pam Niedermayer, Austin, TX

>Except in extremely rare cases, while it's very important the dai be tuned properly for the blade, it's really the blade that's important and holds at least 75% of the plane's value. So if you have to cut the dai off, assuming you have access to a blank dai, then cut it off and don't worry. Then you get to learn how to make dai from scratch. :)

Pam

Re: Japanese plane ID

#7

Re: Japanese plane ID

ThomD

>It is most likely the dai has just picked up moisture, as I am sure you know, or alternatively shruink, but that condition should be entirely reversible. Find some dry spot, preferably not too much for the time being, and just let it return to a normal state. Normally it gets wedged in when there isn't sufficient relief on the sides, rather than the front and back.

Also be aware that the dai can be really hammered hard to release the blade. Take alternate hits from one side to the other , with the blows in line with the abuttments on the sides, otherwise the dai can be broken though I have never seen it. The blows should be @ the same angle as the blade is bedded, and on the upper rounded edge next to the top of the blade. Use something like a 20 ounce hammer. Hold the dai with your weak hand, around blade level so some part of your hand will hold the blade if it pops out. Be aware a dropped blade is heavy enough to do you serious injury. See my earlier post about the sloshing sound in my sandles.

Re: Japanese plane ID

#8

Questions on Dai making

Bob Demers

>Thanks for the advice, Thom and Pam

I can get the blade out, with tapping, and youre right Thom, its both heavy and sharp, quite potentialy damaging to flesh :-) DAMHIKT

This was my first Japanese tool, I picked it up as a kind of curiosity.

There was a few to pick from, but that one draw me in because of its massive blade (thickness wise) and overall condition of the plane.

It came directly from overseas (Japan) so im curious as to its maker.

That blade take an incredible edge and hold it has well. Currently it has a few nicks at the edge so its due for a good workout on my Japanese waterstones (King)+ natural Nagura stone. Currently the blade cannot sit low enough to cut and seems to stick mostly on the sides of the abutments.

I like Pam suggestion of making a new dai, any how-to article out there on how to make these?

Look deceptively simple, but i'll like to read about it before hand.

One last question RE bed angles suggested by Pam.

Does the same blade can be used at all these angles, or the higher angles (more scraping, than shaving) requires a thougher (harder)blade?

Bob, whose English has been know to sound Japanese after a few beers :-)

Re: Japanese plane ID

#9

Re: Questions on Dai making

wilbur

>There's a good written description of how to make a dai for a Japanese plane in Toshio Odate's book on Japanese tools.

There are brief videos and pictures of the process at http://www.shizutanischool.org/, but it will just give you an idea what the process is like.

More photos can be found at http://www.daikudojo.org/Archive/20071028_inomoto_dai_making_seminar.html

Re: Japanese plane ID

#10

Re: Questions on Dai making

ThomD

>"That blade take an incredible edge and hold it has well. Currently it has a few nicks at the edge so its due for a good workout on my Japanese waterstones (King)+ natural Nagura stone. Currently the blade cannot sit low enough to cut and seems to stick mostly on the sides of the abutments."

Baiscaly what you describe is the condition of a new plane that hasn't been used (wether or not that is the actual case here). They often come too tight to the sides, and not low enough, so really you are where you need to be to get to where you need to go.

The first thing you want to look at is whether if the blade is lowered in this dai, would it have clearance at the edge to take a full width shaving (another issue that is often out of wack on new planes and left to individual preference). You can discern this by comparing the width of the available edge of the blade to the width between the abutments on the sole of the plane. Because the plane blade is held by it's edges it has to be docked a little on the corners or the full width cutting edge would try to cut wood that would not be able to clear through the abutments. The solution is to enlarge the grinds at the corners of the blade edge, or potentially narrow the abutments if there is any reason to believe they are too deep and cover too much of the blade.

Once the width is sorted. You probably want to relieve the width of the plane mortise so that hammering in the blade does not split the dai. Remove a judicious amount of material, first measuring the width of the blade if fully sunk, and project those lines top and bottom. Then score the body with a saw and remove the waste with a narrow chisel, etc...

Finally you can pencil the back of the blade so that when inserted it will leave a mark on high points of the dai, and work those down by paring, scraping, or use of a float. Proceed carefully, and remember the Japanese plane is designed to hold the blade under force. You want it to be virtually impossible to overdrive, of course it is possible, but you want to work for a tight fit that is even across the blade, and that naturally returns to battery every time you re-insert the blade and tap it firmly in place. It's a precision tool that should not require brute force to use, but neither should the blade be too easily inserted. Also the blade may find it's place, a little lower, as it is used for the first while, so don't baby it.

The fitting is easy, just proceed slowly.

I don't care what angle you have and what angle you want, you will find this plane cuts everything really well if just seen through to a proper condition. Then you can consider other beddings. As you like.

One minor point is that the back of the blade is usually transverse concave, so that is how the bedding will come out in the plane.

Another minor point is that some planes have a secondary bevel in the bed that supports the bevel of the blade. This is an added complication I will leave unless asked.

Re: Japanese plane ID

#11

Re: Questions on Dai making

Bob Demers

>humm interesting, that's basically what I though althought certainly not to that level of knowledge. Thanks for the insight.

The thing that makes me a tad reluctant to tweak the abutment sides, or touch up the blade sides, is the fact that this plane used to cut beautifully. Having moved a lot around the country since i suspect that the dai has swollen a bit and thighten its grip on the blade (?) So my fear is that if i remove wood, would it not become too loose down the road?

Mind you as is, it does not cut whatsoever, so I brought it in from the shop and will leave it sit at home for a while to see how it react. Since we are into the heating season (electric here) Im guessing that its humidity level will go down.

So, Im guessing I should wait a bit then proceed lightly with the teaking?

Thanks again for your insight, I'm in new territory here :-)

Bob

Re: Japanese plane ID

#12

What I got so far from that forum

Bob Demers

>So far the best guess i got (from Steve) is that it is a common Hira Kanna (flat plane used for smoothing)

The main characters (center) read "Tsugu Hiro".

He think the two characters to the right read "tokusen" (the detail is not sharp, could be wrong) meaning special selection -

and the characters on the lower left are quite cryptic - not the usual kanji, so Steve had no idea what they say.

Does any of that ring any bells with anyone??

By the way, I was quite surprised to find out that Steve is from Lawrencetown NS, that is not far from where I used too live when I got that plane and not far neither from where it came from.

It's a small world after all :-)

Bob, amused at the fact that I posted on a Japanese WW forum hosted in Australia, just to be answered from someone living not far from where the plane came from, cool!

Re: Japanese plane ID

#13

Isn't globalization wonderful? :)

Pam Niedermayer, Austin, TX

>You may also have noticed parts 1, 2, and 3 of how to sharpen a plane blade in that forum. Great stuff.

Basically I agree with everything Thom and Wilbur said, but I do want to emphasize that the actual bed must be slightly rounded to fit the blade. A 1/8" paring chisel works for tuning the abatements, you don't need a float.

Thom's advice to put the plane inside for a couple of months is excellent advice.

Pam