Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

This $39 jig will make you a WOODWORKING GOD!

Hand plane storage

Posts

Hand plane storage

#1

Hand plane storage

Guy

>Hello, I just acquired a metal tool chest that I will be storing my tools in. My question is for the drawers that will hold my planes. What would you put on the bottom for the planes to rest on? I am thinking about 1/8 inch plywood. I have been using shelf liner that looks like router pads and I will use that for the rest of the drawers but I want my planes to stand on wood. Any thoughts, etc. I know I should store them in nice wood tool chests etc but at this stage of the game the metal chests are cheap, sturdy, and will easily last till all my other projects are done. Any opinions are more than welcome.

Re: Hand plane storage

#2

Re: Hand plane storage

Bill Houghton, moderately nice in Sebastopol, CA

>Depending on your climate, the metal chests may be fine. I live on California's North Coast (an hour north of San Francisco), which has relatively low humidity, but very damp winters, and I use metal chests for my tools (not yet my planes, but it's probably coming - just need to save up the pennies), and they've been fine.

People in higher humidity climates sometimes express worry about storing tools in metal chests - I note that there are lots of machinist's chests made of metal, and machinists are obsessive about rust, for good reason. The classic machinist's top chest lines the drawers with felt, but the underside of the drawer above is just plain metal.

But I can't speak for humid country - it's been 35 years since I lived in Michigan, and I don't have any direct experience on the subject.

Plywood's fine. I have come to believe in cleats that support the plane at front and back, leaving the mouth suspended in air. This lets me leave the plane iron set for cutting, so I can just grab the plane and go. If you have the depth in your plane drawers, you might consider 1/8" ply or masonite with 1/8" or 1/4" cleats hot glued to the ply. You can't really use the shelf liner with this approach - hot gluing to it might be hard.

For chisels and such, the router pad like material is great - tools don't roll around easily, and you can just set the tools in next to each other, and they'll stay in place.

Re: Hand plane storage

#3

Re: Hand plane storage

Tom MacGregor

>McMaster Carr has adhesive backed cork sheets designed for use as compressable gasket material. It can be cut with a utility knife, is soft enough to not damage edges and rugged enough to hold up as a drawer liner.

Re: Hand plane storage

#4

Good idea

Bill Houghton, moderately nice in Sebastopol, CA

>Your local auto parts store will also have cork gasket stock. You'd have to glue it yourself, but you might find, once it straightened out, that the other planes in the drawer would hold it down just fine.

You'd have to do price comparisons to see which would be less expensive.

Re: Hand plane storage

#5

Re: Good idea

ThomD

>LV sells the cork stuff, at least that is where I lat bought mine. If worried about rust, buy a bottle of Camelia oil. The smallest amount one can spread on a tool will solve any problem. It's nice enough people put it in their hair, I am told. It doesn't seem to cause problems with glue joints etc... if used sensibly.

Re: Hand plane storage

#6

Re: Hand plane storage

Neal in San Jose

>I agree that wood is a better idea than the router pads. I used the router pad for storatge of some seldom used planes, and they now have the pattern of the pad lightly etched into the bottom. It may have taken several months of non-use for that to happen, and I'm not sure exactly what did happen, but I don't do that any more!

Re: Hand plane storage

#7

mine sit on carpet backing

Bill Tindall, E.TN

>and I think carpet would be fine too.

Re: Hand plane storage

#8

Re: Hand plane storage

waltc

>I use cork myself, on a wood bottom. I cut the cork to support the front and rear of the plane, and leave the blade not touching anything.

I have heard two things about rust--the typical kitchen shelf liner tends to encourage it if steel is left in contact with it long term, and that wood storage is better because it "buffers" the humidity.

I can't vouch for either, just passing on rumors.

Walt C

Re: Hand plane storage

#9

Re: Hand plane storage

Bob Demers

>That happened to me too, and it did not took months to leave that 'pattern' on my beloved Bedrock 602, really pissed me off.

I think its because my black router mat was some sort of slightly gummy rubber?

Nonetheless, never again

I always store my plane up, never sideways. And I dont worry about damaging the edge (they keep whatever set they last had when used)

I dont drag them, I just put them down on the bench.

In long term storage: if I put them away I'll retract the iron, if simply stored in tool boxes or in cabinet, I put a small cleat under the toe, just to elevated the sole off the floor. Not so much to protect the edge as to protect the sole from rust.

Bob, with way too many planes according to some :-)

Re: Hand plane storage

#10

Drawer Liner

David Miller from Iowa

>I have mine set on basic drawer liner from WalMart. I was concerned about leaving a mark or an etch - but 2 years with absolutely no issue.


img

Re: Hand plane storage

#11

That's because your planes...

Scott Burr in Ben Lomond, CA

>Are all grungy and rusty!

;^) Just kiddin' Dave.