Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

100+ Wood Species + Full-Shop Services: Lumber, Veneer, Tools & CNC. Everything in One Place.

The sign I'm going to hang in my shop

Posts

The sign I'm going to hang in my shop

#1

The sign I'm going to hang in my shop

wilbur

>I need to hang a sign in my basement shop.

It will read:

"How to fix most problems while you're down here, chucklehead.

Step 1. Check to make sure your tools are sharp.

Step 2. If you are still having trouble, go back to step 1."

Don't ask. It's just too embarrassing.

:@)

Re: The sign I'm going to hang in my shop

#2

Re: The sign I'm going to hang in my shop

Brent Smith, Montreal

>C'mon Wilbur....if you can't be embarrassed here, where can you be :). What happened..........

Re: The sign I'm going to hang in my shop

#3

LOL !

steve mackay

>

Re: The sign I'm going to hang in my shop

#4

Re: The sign I'm going to hang in my shop

Stuart Hough

>Don't worry Wilbur...we've ALL been there a time or three!

Re: The sign I'm going to hang in my shop

#5

I have come to the conclusion that sharp is about

Bill Houghton, sunny in Sebastopol, CA

>90% of "tune up" on most hand tools.

And, yes, you're sure not alone. I've even embarrassed myself in front of people with tools that once were sharp, but not when I was using them.

Re: The sign I'm going to hang in my shop

#6

Ahhh come on Wilbur spill it!

Scott Burr in Ben Lomond, CA

>I promise I won't laugh...well not too much.

Re: The sign I'm going to hang in my shop

#7

Okay, okay

wilbur

>There were actually two incidents. Here's the scoop:

1. I was having trouble face planing some maple, and was getting some tearout. I thought the problem was that I had brought my Japanese plane to Berea for show and tell, and thought that the problem was due to the body of the plane moving, since I had it in the trunk of my car for the trip from NJ to Berea and back. So I go through a round of tuning up the body and sole of the plane. Guess what the actual issue was?

2. I found that I was having trouble on my lathe with catche, spirals, and a general lack of control with my skew chisel, where I hadn't had issues before. I recently had taken a lesson on turning beads with a spindle gouge. I was actually more comfortable with the skew chisel than the spindle gouge prior to this lesson. The lesson was really good, and I thought that the problem that I was having now was due to confusing the techniques used for these two tools, sort of like trying to switch to snowboarding from skiing. Guess what the actual issue was?

Re: The sign I'm going to hang in my shop

#8

Re: Okay, okay

Todd O. Cronkhite Maine Native Presently Away

>1) The blade had been removed and not properly reset?

2) you wasn't using the skew that you thought you where?

T.O.

Re: The sign I'm going to hang in my shop

#9

This is very similar to the time I spent...

Bill Houghton, sunny in Sebastopol, CA

>half a day trying to figure out why the bathroom heater wouldn't work (which involved crawling under the house from the crawlspace entrance almost to the farthest reaches of the crawl space), completely forgetting that I'd installed a wall switch to turn it off, since the thermostat settings didn't run low enough.

And, yes, I've sworn at tools when all I'd have had to do was sharpen them more times than I can remember.

Thanks for letting me know I'm not alone, Wilbur. Takes courage.

Re: The sign I'm going to hang in my shop

#10

Hmmmmm...

Scott Burr in Ben Lomond, CA

>Blade installed backwards? As far as the turning tools go, well I think your on the right track. Never too sharp eh?!?