Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Good Hope Hardwoods - Walnut Slabs & Specialty Hardwood Lumber

Undoing electrolysis

Posts

Undoing electrolysis

#1

Undoing electrolysis

Joe Grittani

>Greetings from Dayton, Ohio.

Here's another question, the thing I'm best at. A friend called last week to tell me that he had finally tried electrolysis on a Stanley plane. It took off the rust, alright. It also took the nickel plating off of the lever cap, but he could live with that.

Impressed with his success, he fired it up again to clean some plane blades without mixing up a new batch of mojo juice and, lo and behold, the blades came out nickel plated. Is there a way to strip this off, and what might he have done wrong to get this result aside from not tossing the first batch of juice?

TIA

Joe Grittani

Re: Undoing electrolysis

#2

Re: Undoing electrolysis

Bruce, a MN Galoot

>I'd be willing to bet that he hooked up the blade to the wrong pole of the current. Have him reverse the way the blade is connected to the power source and his problems (as well as the nickle plating) will disappear.

Bruce

Re: Undoing electrolysis

#3

Re: Undoing electrolysis

Todd O. Cronkhite Maine Native, Presently Away

>The only reason I can think of that this happened is that the rods he was using might of been galvanized. If not, then perhaps he has stumbled into some type of plating technique!! Seems to me that electroylis was used to do plating way back when.

At any rate the tool that is to be zapped gets the NEGATIVE clamp of the battery charger.

The best way I have found to remember this is to say to myself "Rust on the tool is a negative".

T.O.

Re: Undoing electrolysis

#4

reverse leads

Bill Tindall, E.TN

>The only way to deposit nickel under any circumstances without violating various laws of physics and chemistry is to have reversed the leads. However, I don't believe the premise even if the leads were reversed, for more reasons than I am willing to type right now. Whatever he is complaining about is not nickel plating from nickel stripped from the first plane. What you describe is the equivalent of saying a friend rolled a ball uphill and when he let go it continued to roll up hill.

The above presumes he used carbonate or hydroxide in the solution and not Mojo juice which could have violated various laws of physics.

Re: Undoing electrolysis

#5

correction

Bill Tindall, E.TN

>Must not type while nearly asleep. Spent 6 hours wedged on back in attic reinstalling soffit vents and adjusting insultaion prior to reinsulation, then two more stooped supervising the reinsulation. Can barely move. R40 (its warm in these parts) and all the heat ducts are buried.

Anyway, reversed leads is not the possibility and forget rolling balls, unless leads were hooked up equivalently, backwards or correct, for each plane. Then first message stands.

There is some very remote possibility that the leads were reversed for the first plane. If there was nickel plating it would have dissolved under these conditions but I am extremely skeptical that it would have redeposited with the leads properly applied to the second plane. It is not trivial to get nickel to deposit on iron and I doubt your friend blundered into conditions that would do it.

Whatever the friend is complaining about is not nickel plated from nickel stripped from the first plane. If the leads were properly applied in the first plane any coating removed would have been mechanically removed by the action of bubbles (dare I say scrubbing bubbles?) and settled asnickel metal in the tank where it still is.

Re: Undoing electrolysis

#6

Careful here

Denis Ch�nard, Orl�ans, Ont.

>Not an expert by any means, but I did zap a few tools in the past. The electrode used to close the circuit is sacrificial, and gets eaten away during the electrolysis process (unless it's stainless steel). If one reverses the leads it might end up eating away the tool that is intended to be de-rusted.

I might very well be missing something here, but I would advise caution.

DC

Barred from the shop for six weeks (hernia surgery)

Re: Undoing electrolysis

#7

OT - my sympathies, Bill

Bill Houghton, sunny in Sebastopol, CA

>"Spent 6 hours wedged on back in attic reinstalling soffit vents and adjusting insultaion prior to reinsulation, then two more stooped supervising the reinsulation. Can barely move."

My deepest sympathies. The post-WWII addition on our old house has attic heights that, in spots, require any workers in the space be about 6" thick and fourple-jointed, leading to a lot of acrobatics that would leave modern dancers swearing. I spent many a weekend over what was either two years or two centuries, depending on whether you're measuring chronological or perceptual time, in that part of the attic when I rewired the house, and since with some remodels. Sounds like yours would feel very familiar.

Good-o on the insulation, though: it does pay off. LOML is already mentioning the improvement from the floor insulation that I'm not quite done with.