Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Veritas - Innovation in Tools

Sargent plane parts?

Posts

Sargent plane parts?

#1

Sargent plane parts?

Bill Houghton, Sebastopol, CA

>I've had a couple of minutes - not much - to admire my new Sargent No 79 (like the Stanley 78, though simplified - clearly competing in the "cheaper than" market), and have determined that a No. 78 fence will fit, but that the fence rod requires a different thread pitch.

Two questions:

1. I haven't yet confirmed the thread pitch. Anyone happen to know?

2. Does anyone make reproduction parts for these planes? Google didn't help much, although I could have spent hours looking at airplane parts or prints of John Singer Sargent paintings.

Re: Sargent plane parts?

#2

Dominic in Bucks County PA

Re: Sargent plane parts?

Dominic in Bucks County PA

>

Bill,

You might want to talk to Walt Q. or Clint (aka: Leonard Bailey) over at WoodNet. Both of these guys have a bushel of spare parts for just about every "common" plane in existance.

Clint helped me out when I needed a chip breaker and iron for my old (and recently sold!) Sargent No6. I'd call Walt rather than email. It's quicker and he's a hoot to talk to.

It's a long shot but you might also want to check and see if St. James Bay sells the parts you need.

See ya around

Dominic

Re: Sargent plane parts?

#3

It looks like 22 threads per inch

Bill Houghton, Sebastopol, CA

>for a 1/4" or No. 14 (not sophisticated enough to measure which) screw. Not even my uncle's 1950's Starrett catalogue, which has some very strange thread pitches, lists 1/4-22, so it's definitely a before-standardization thread size/pitch. I've followed Dominic's suggestion and am looking for a factory piece - otherwise, I'd have to re-thread it (interestingly, Stanley, famous amongst us all for its offbeat thread pitches, used 1/4-28, modern standard fine thread, for the fence rod, so I could use one of those), OK for a user tool, though disappointing for hypothetical future collectors.

Re: Sargent plane parts?

#4

Re: It looks like 22 threads per inch

Alan DuBoff

>Bill,

1/4-22 is not a common size, but in my Machinery's Handbook (one of the bibles for machinists) they list the wire sizes to use for measuring such a thread, so it is a valid thread. I don't think it is very common at all though. There are several references to 5/16-22, but only one reference to 1/4-22.

Regards,

Alan

Re: Sargent plane parts?

#5

I did fine machine screw size 16-22

Bill Houghton, Sebastopol, CA

>in my uncle's Starrett catalog - also not common, at least in the modern Ace hardware. I don't know enough to know how close a #16 is to a #14, which itself is close to 1/4".

Well, I've got some feelers out to rust dealers, so we'll see what turns up. Kind of silly spending time on it - I remember thinking, when I bought it, "oh good, now I'll have a carpenter's rabbet without a fence on it, so I can use it freehand [something that comes up more often than fenced use in my carpentry]," and now, here I am, wondering about a fence.

Re: Sargent plane parts?

#6

That's "did FIND"

Bill Houghton, Sebastopol, CA

>

Re: Sargent plane parts?

#7

1/4 is between 14 and 16

Alan DuBoff

>Well, like I said there is a 1/4-22 listed in a table of wire sizes to check with, it just looks uncommon, AFAICT.

The numbers start at .060" for a number 0, and they increment 013" for each number, best I can tell.

0 - .060"

1 - .073"

2 - .086"

3 - .099"

4 - .112"

...

14 - .246"

1/4 - .250" <-- between 14 and 16, 15 is not a common size

16 - .268"

I can't explain the entire system, I use my Machinery's Handbook to get the numbers I need. :-)

Regards,

Alan