Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Reach the woodworkers who ACTUALLY BUY

Home made tenon cutter

Posts

Home made tenon cutter

#1

Home made tenon cutter

Bob in Green Bay

>I am interested in fiddling a bit with some twig furniture, similar to Mr. Mack.

I do not have a circular tenon cutter but thought I could make my own, at least to cut a few to see if I like doing it. The premanufactured ones are a bit pricey just to try something out.

I was thinking 5/8" diameter. I thought perhaps hole in a nice bit of oak, slightly larger than 5/8" with a piece of an old leaf spring, slotted and shaped as a blade with a notch in the side of the oak form to allow the shavings out. I would harden the steel with a torch and quench in water.

I vaguely recall similar by Roy Underhill but can not find again.

Any ideas?

Bob

Re: Home made tenon cutter

#2

Re: Home made tenon cutter *LINK*

Pam Niedermayer, Austin, TX

>Here are some fairly cheap ideas.


Rounders at Garrett Wade

Re: Home made tenon cutter

#3

Re: Home made tenon cutter *LINK*

Dick Coers

>Spent some time trying to find rounder plane plans. No luck but found a pic of a fantastic looking tool.


wood dowel plane

Re: Home made tenon cutter

#4

Re: Home made tenon cutter

ThomD

>Roy has done rounders, not sure if they were that small. But the principle is the same. You can quench in water, but oil or bacon fat, etc... is better for most plain steels.

In the classic modern approach to ladder back chairs the tenons are actually cut by hand. Check out John Alexander's video and book. The book has been around a long time, so it probably can be dragged up by your library. The assembly counts on a very nuanced fit which is hard to deal with on a machine that requires some setting, and then is difficult to addapt to subtle changes. The tenons are sometimes flattened by hand on the side. The thing is that if you are doing the drill it, sharpen it, and epoxy it chair, then your need for a machine is even less since the fit isn't hyper critical. The main reason to have it is to make it easy and fast, but if you are planing on just a few chairs it might be simpler to simply whittle the tenon, than make a rounder.

Re: Home made tenon cutter

#5

Re: Home made tenon cutter

Adam Cherubini

>For twig furniture, I think you want something more like LV's tenon cutters. It should look more like a trumpet's bell. You want to take an irregular and over sized branch and just stick it in the rounder and be left with a good tenon. The tenon usually needs to be sized very carefully and precisely so you can use a standard boring bit like a stanley power bore to produce the hole. Twig furniture works best when this tenon cutter and drill combination produce a nice tight fit.

Adam

Re: Home made tenon cutter

#6

Re: Home made tenon cutter

Jim Crammond in Monroe, Mi.

>Bob,

Drew Langsner shows plans for a tapering plane on page 32 of The Chairmaker's Workshop. It is similar to the Garrett Wade planes.

Re: Home made tenon cutter

#7

Re: Home made tenon cutter *LINK*

Patrick Gibbons, Katy, TX

>Check out this link for a home made hole taper.


http://www.greenwoodworking.com/reamer.htm

Re: Home made tenon cutter

#8

Re: Home made tenon cutter

Stephen Shepherd in the State of Deseret

>Bob,

If you have a lathe you can make one from wood with a metal cutter, like these.

http://www.fullchisel.com/image198.gif

http://www.fullchisel.com/image200.gif

Stephen

Re: Home made tenon cutter

#9

Re: Home made tenon cutter

ThomD

>I made one of those taper reamers by hand with a drawknife etc... Works great. I prefer it in some respects to the quality ones made of steel.

Re: Home made tenon cutter

#10

Re: Home made tenon cutter

Bob in Green Bay

>Thanks all for the responses! I have enough in my head now to try something. It is getting cold out - moving back inside.

Bob