Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

200+ woodworking book reviews

making scratch stock

Posts

making scratch stock

#1

making scratch stock

McKay

>I have an old back saw that I would like to use for making scratch stock. The problem is that it resists the hacksaw, file and aviation snips. Is this just too tempered or can I anneal it to make it softer? What say ye old wise ones?

Re: making scratch stock

#2

Jack Guzman from Maine

Re: making scratch stock

Jack Guzman from Maine

>Clamp it in a vise and break it to get it down to size,then grind it to shape.---Jack

Re: making scratch stock

#3

NO direct experience

Bill Houghton, Sebastopol, CA

>I've seen other threads in which people talk about scribing it with a carbide scriber several times to establish a line, then bending it back and forth. I've done similar things with sheet metal and other stock; just never saw steel. Certainly, that's how glass cutting works.

The key, I think, is to get a line of weakness established to encourage the bending to focus on where you want the break to occur.

Re: making scratch stock

#4

Re: making scratch stock

McKay

>What would happen if a plasma cutter was used to cut it up? Do you think that it would ruin the steel?

Re: making scratch stock

#5

Re: making scratch stock

Derek Cohen (in Perth, Australia)

>I would scribe it with a fine wheel on a Dremel, then snap it off and joint the ends with a file.

This is what I do with used bandsaw blades. I file these without any heat treatment. The files skate a little on the hardish steel, but they remove the waste and the end result is good.





Regards from Perth

Derek

Re: making scratch stock

#6

An old way

David Barnett - SW Florida

>...involves making a simple scoring tool from an old or broken file. You could also likely make one of these with a hex key ala Derek, I'd suppose.

Anneal the tang with a propane or mapp torch and let it cool slowly. then bend the tip to approximately ninety degrees (use a machinist's vise and lever -- a pipe works well). Bevel the end into a 'V' shape and grind a flat that will scrape a shallow groove when pulled along a straightedge. Harden and quench but do not temper. Hone the flat with a diamond slip or bench stone. Handles are optional for repurposed files but essential for hex keys and other adaptations.

To use, pull lightly for a few passes until a scratch is deepened enough to self-track, then deepen until a shallow but distinct V-groove is visible. Align the score in a vise, cover with a folded rag, don eye protection, place a straight strip of wood thick enough to distribute force from mallet blow opposite grooved side and strike a sharp mallet blow to the caul. The steel should snap cleanly.

Obviously, this description is for cuts up to several inches. Shorter cuts work very well with the Dremel and separating disc method.

TIP: If you shape your V-bevel to form a right angle when closed, this makes a very crisp-looking folded corner in thicker nonferrous metals for all sorts of hardware, hinges, corner plates, metal boxes, and so on. Don't cut all the way through, of course. For stronger folds one can braze or silver solder with a torch. Flux the entire piece and use as little solder as possible. Plunging while still hot into hot water or pickle will remove the flux.

Re: making scratch stock

#7

You'd have to grind back

John in NM

>About 1/16" from the cut line, maybe more depending on the steel, the cutter settings, etc. Not as easy as score and break I'd think.

Re: making scratch stock

#8

Dremel with cutting wheel.

steve mackay

>

Re: making scratch stock

#9

Where you been David?

Scott Burr in Ben Lomond, CA

>I for one have missed you around here.

Re: making scratch stock

#10

I'm a wretched prodigal backslidin' reprobate

David Barnett - SW Florida

>But sincerely, thank you for asking, Scott.

I've been busy, and not just for myself. Although I've done some woodworking, most has relied heavily on considerable electron attrition where sheet goods were often involved. Handtooling (mostly with files and scrapers) was limited to detailing, fitting joints and veneering. Thick aluminum plate was bandsawn and attached with high-tech machine screws and modern adhesives. Design elements are stacked plywood edges rather than faces, and the casework has no handtool finesses.

Luminaires are hybrids of thick aluminum, MDF with quarter-sawn BRW veneer, non-orange non-shellac synthetic resin mineral (mica) shades were formed with a heatgun from large sheets of the stuff. Nothing organic. No curves, streamlining and somewhat retro. Where solid woods ARE used, they're usually bleached, or bleached-dyed-bleached again. While incandescent bulbs will initially be used, compound LED bulbs will replace them. Newer shadeless lamps will employ cast glass (my own PDV) and other somewhat indy materials.

I've been absorbed in audio isolation tactics and folded transmission line speaker designs employing very small full-range drivers. Sheet goods, tablesawing and veneering, of course. Simple and cheap electronics have produced a very fast, very musical and lively integrated stereo amplifier (a 'gainclone') with external power supply. I've already started a second one. I don't get out much.

There's more, but I'll stop with these heresies for now. Obviously, I'm going through a phase. Be patient. You never know when I'll return to the fold.

Re: making scratch stock

#11

Why so much trouble?

Todd Hughes

>Man you guys like to do things the hard way !

Ive made lots of scratch stock blades as well as scraper blades out of old saws and all I ever did was scribe a line into the blade with the edge of an old file. Doesn't have to be deep and you only need to scribe it once. Then put in a vise and snap it off by bending down on the excess while taping it down with a hammer.If your vise jaws that close up tight you will have a near perfect edge. If your vise isn't in the best condition just put two piece of flat bar in it with the saw piece in between....This always worked well and was easy , fast and simple to do...Guess I was lucky that I didn't know It had to be lots more complicated, eh?

Heating up, reshaping, anealing, tempering, grinding, sharpening files, dremals and abrasive wheels ?... I think some people must have to much time on thier hands.....Todd

Re: making scratch stock

#12

Reprobate!?! Sorry for the late reply David...

Scott Burr in Ben Lomond, CA

>Indulging in TL speakers... I think not. Their fascinating and I've played with them myself.

Still working on those luminaries eh? I'd love to see a pic of the modern designs and CMF work going into them. Drop me a pic if you can.

Anyway, good to see you're still here you silver tonged devil.